Operating Instructions
Table Of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 BTR-800 Base Station
- CHAPTER 3 TR-800 Beltpack
- CHAPTER 4 TR-825 Beltpack
- CHAPTER 5 Initial Equipment Setup
- Unpacking
- Antenna Connection
- Antenna Polarization
- Distance between Antennas
- Antenna Placement
- Improving Reception and Increasing Range
- Base Station Set-up
- Location
- Power Connection
- Transmit Switches
- Internal Transmit Switches
- Intercom Switch
- Intercom Interface
- Dual Listen Functionality
- Auxiliary Input/Output
- Internal Auxiliary Input Routing Switch
- Stage Announce / Relay Contacts
- Base Station Link
- Beltpack Setup
- Antenna Connection
- Transmit Mode
- Headset Connection
- CHAPTER 6 Pre-Walk-Thru Checklist
- CHAPTER 7 System Operation
- Frequency Plan Overview
- Factory-Defined Groups
- User-Programmable Groups
- System Quick Start
- Base Station Operation
- Power
- Local Headset
- Portable Station Connect
- Intercom A and B
- Auxiliary
- Display Contrast
- BTR-800 Menu Structure
- Main Screen Flowchart
- Power-Up Screen
- Operating Screen
- Beltpack Activity Code Definitions
- Group/Channel Select
- Group/Frequency Select
- Frequency Edit (User-Programmed Groups Only)
- ClearScan™
- Special Key Sequences
- Lockout
- Copy
- 1st Use Default
- Factory Default
- Beltpack Operation
- On/Off and Volume Control
- Battery Check
- Talk Button
- Microphone Gain
- Audio Channel Select Button
- Stage Announce (SA)
- Wireless Talk Around (WTA)
- TR-800 Menu Structure
- Beltpack Menu Structure
- Power-Up Screens
- Group/Channel Screen
- Transmit Screen
- Receive 1 Screen
- Receive 2 Screen
- ClearScan™
- Stage Announce Enable/Disable
- Wireless Talk Around Enable/Disable
- Audio Channel A or B Disable/Enable
- Talk Button Latch on/Latch off
- Special Key Sequences
- Lockout
- 1st Use Default
- Factory Default
- TR-825 Menu Structure
- CHAPTER 8 System Walk-Thru
- CHAPTER 9 Troubleshooting
- CHAPTER 10 Tech Tips
- CHAPTER 11 Battery Information
- CHAPTER 12 Intercom Systems Specifications
- CHAPTER 13 Accessories and Replacement Parts
- CHAPTER 14 Certification Information
- CHAPTER 15 Three Band Base Stations
BTR-800, TR-800, TR-825 System Operation 47
Special Key Sequences
Lockout
•
Press [UP]+[DOWN] for three seconds to lock or unlock
the base station. Pressing [MENU] will still function to
view screens, but [SET] will no longer start any editing.
ClearScan™, First use, Factory default are no longer
accessible. The intercom channel A and B front panel 2-
wire/4-wire selection is also locked into place. A padlock
icon will be displayed on the second line of the display to
the far left as an indication that the base station is locked
out.
Copy
•
Press [SET]+[DOWN} for 3 seconds to copy any currently
display group to a user-programmable group. Copy can be
done from the group/channel select, group/frequency select
or frequency edit screen. Once pressed, the words, “copy
to” are displayed on the screen with the first empty user-
programmable group flashing. If all the user-programmed
groups were full, than the first programmable group is
displayed. The [UP] or [DOWN] buttons may be used to
select a different user-programmable group, if desired.
Pressing [SET] pastes frequencies/channels to the group
and takes the user to the frequency edit screen with T1
flashing.
1st Use Default
•
Press [MENU] while turning on the base station to enter the
1st use default setup screen. This places the unit on group
01A with the four receivers set to channels 1-4 of the group.
Any user-programmed frequencies that had been
entered previously are retained. If lockout had been
activated, the beltpack comes up where it was last left
regardless of [MENU] being pressed on power-up.
Factory Default
•
Pressing all four buttons [MENU]+[SET]+[UP]+[DOWN]
at the same time for three seconds places the unit on group
01A with the four receivers set to channels 1-4 of that
group. This is just like base station 1st use default, except
that all user-programmed frequencies that had been
entered previously are erased. This function may take
several seconds. If lockout had been activated, the beltpack
comes up where it was last left regardless of these four keys
being pressed.