Operating Instructions
Table Of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 BTR-800 Base Station
- CHAPTER 3 TR-800 Beltpack
- CHAPTER 4 TR-825 Beltpack
- CHAPTER 5 Initial Equipment Setup
- Unpacking
- Antenna Connection
- Antenna Polarization
- Distance between Antennas
- Antenna Placement
- Improving Reception and Increasing Range
- Base Station Set-up
- Location
- Power Connection
- Transmit Switches
- Internal Transmit Switches
- Intercom Switch
- Intercom Interface
- Dual Listen Functionality
- Auxiliary Input/Output
- Internal Auxiliary Input Routing Switch
- Stage Announce / Relay Contacts
- Base Station Link
- Beltpack Setup
- Antenna Connection
- Transmit Mode
- Headset Connection
- CHAPTER 6 Pre-Walk-Thru Checklist
- CHAPTER 7 System Operation
- Frequency Plan Overview
- Factory-Defined Groups
- User-Programmable Groups
- System Quick Start
- Base Station Operation
- Power
- Local Headset
- Portable Station Connect
- Intercom A and B
- Auxiliary
- Display Contrast
- BTR-800 Menu Structure
- Main Screen Flowchart
- Power-Up Screen
- Operating Screen
- Beltpack Activity Code Definitions
- Group/Channel Select
- Group/Frequency Select
- Frequency Edit (User-Programmed Groups Only)
- ClearScan™
- Special Key Sequences
- Lockout
- Copy
- 1st Use Default
- Factory Default
- Beltpack Operation
- On/Off and Volume Control
- Battery Check
- Talk Button
- Microphone Gain
- Audio Channel Select Button
- Stage Announce (SA)
- Wireless Talk Around (WTA)
- TR-800 Menu Structure
- Beltpack Menu Structure
- Power-Up Screens
- Group/Channel Screen
- Transmit Screen
- Receive 1 Screen
- Receive 2 Screen
- ClearScan™
- Stage Announce Enable/Disable
- Wireless Talk Around Enable/Disable
- Audio Channel A or B Disable/Enable
- Talk Button Latch on/Latch off
- Special Key Sequences
- Lockout
- 1st Use Default
- Factory Default
- TR-825 Menu Structure
- CHAPTER 8 System Walk-Thru
- CHAPTER 9 Troubleshooting
- CHAPTER 10 Tech Tips
- CHAPTER 11 Battery Information
- CHAPTER 12 Intercom Systems Specifications
- CHAPTER 13 Accessories and Replacement Parts
- CHAPTER 14 Certification Information
- CHAPTER 15 Three Band Base Stations
54 System Operation BTR-800, TR-800, TR-825
Receive 2 Screen
The Receive 2 screen allows the user to set the beltpack receive
2 frequency. This corresponds to the base station’s transmit 2
frequency. In factory-defined groups receive 2 is not
changeable. User-programmable groups will allow the user to
change the frequency in 25 kHz steps.
• Press [MENU] three times from the group/channel screen to
arrive at the receive 2 frequency screen.
• (User-Programmable Groups Only) Press [SET] to edit the
frequency. The number will start flashing. Factory-defined
groups can’t be changed, so pressing set will do nothing at
this screen. User-programmed groups will start flashing and
allow the user to change the frequency in 25 kHz steps.
• (User-Programmable Groups Only) Use the [UP]/[DOWN]
arrow buttons to change the frequency.
• (User-Programmable Groups Only) Press [SET] to place
the beltpack on the frequency selected. If set is held down,
during that time the group is displayed so the user is aware
of what group the unit has been placed. Once set is released,
the unit returns to the receive 2 frequency screen with
nothing flashing.
• (User-Programmable Groups Only) Pressing [SET] once
more will start the editing sequence over again. Pressing
[MENU] during receive 2 frequency edit will end editing
and send the user back to the receive 2 screen without any
changes.