Operating Instructions
Table Of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 BTR-800 Base Station
- CHAPTER 3 TR-800 Beltpack
- CHAPTER 4 TR-825 Beltpack
- CHAPTER 5 Initial Equipment Setup
- Unpacking
- Antenna Connection
- Antenna Polarization
- Distance between Antennas
- Antenna Placement
- Improving Reception and Increasing Range
- Base Station Set-up
- Location
- Power Connection
- Transmit Switches
- Internal Transmit Switches
- Intercom Switch
- Intercom Interface
- Dual Listen Functionality
- Auxiliary Input/Output
- Internal Auxiliary Input Routing Switch
- Stage Announce / Relay Contacts
- Base Station Link
- Beltpack Setup
- Antenna Connection
- Transmit Mode
- Headset Connection
- CHAPTER 6 Pre-Walk-Thru Checklist
- CHAPTER 7 System Operation
- Frequency Plan Overview
- Factory-Defined Groups
- User-Programmable Groups
- System Quick Start
- Base Station Operation
- Power
- Local Headset
- Portable Station Connect
- Intercom A and B
- Auxiliary
- Display Contrast
- BTR-800 Menu Structure
- Main Screen Flowchart
- Power-Up Screen
- Operating Screen
- Beltpack Activity Code Definitions
- Group/Channel Select
- Group/Frequency Select
- Frequency Edit (User-Programmed Groups Only)
- ClearScan™
- Special Key Sequences
- Lockout
- Copy
- 1st Use Default
- Factory Default
- Beltpack Operation
- On/Off and Volume Control
- Battery Check
- Talk Button
- Microphone Gain
- Audio Channel Select Button
- Stage Announce (SA)
- Wireless Talk Around (WTA)
- TR-800 Menu Structure
- Beltpack Menu Structure
- Power-Up Screens
- Group/Channel Screen
- Transmit Screen
- Receive 1 Screen
- Receive 2 Screen
- ClearScan™
- Stage Announce Enable/Disable
- Wireless Talk Around Enable/Disable
- Audio Channel A or B Disable/Enable
- Talk Button Latch on/Latch off
- Special Key Sequences
- Lockout
- 1st Use Default
- Factory Default
- TR-825 Menu Structure
- CHAPTER 8 System Walk-Thru
- CHAPTER 9 Troubleshooting
- CHAPTER 10 Tech Tips
- CHAPTER 11 Battery Information
- CHAPTER 12 Intercom Systems Specifications
- CHAPTER 13 Accessories and Replacement Parts
- CHAPTER 14 Certification Information
- CHAPTER 15 Three Band Base Stations
BTR-800, TR-800, TR-825 System Operation 63
Receive 1 Screen
The Receive 1 screen allows the user to set the beltpack receiver
1 frequency. This corresponds to the base station’s transmit 1
frequency. In factory-defined groups receiver 1 is not
changeable. User-programmable groups will allow the user to
change the frequency in 25 kHz steps.
• Press [MENU] twice from the group/channel screen to
arrive at the receive 1 frequency screen.
• (User-Programmable Groups Only) Press [SET] to edit the
frequency. The number will start flashing. Factory-defined
groups can’t be changed; so pressing set will do nothing at
this screen. User-programmed groups will start flashing and
allow the user to change the frequency in 25 kHz steps.
• (User-Programmable Groups Only) Use the [UP]/[DOWN]
arrow buttons to change the frequency.
• (User-Programmable Groups Only) Press [SET] to place
the beltpack on the frequency selected. If [SET] is held
down, during that time the group is displayed so the user is
aware of what group the unit has been placed. Once [SET]
is released, the unit returns to the receive 1 frequency screen
with nothing flashing.
• (User-Programmable Groups Only) Pressing [SET] once
more will start the editing sequence over again. Pressing
[MENU] during receive 1 frequency edit will end editing
and send the user back to the receive 1 screen without any
changes.