Step-by-step Instructions

ManualsBrandsRuckus Wireless ManualsComputers & AccessoriesR650 Access Point

R650 Access Point

Quick Setup Guide

This Quick Setup Guide pr

vides step-by-step instructions on

how to install and begin using your Ruckus R650 dual-band

802.11ax indoor Wi-Fi access point (AP).

FIGURE 1 R650 Access Point: Top View

This Guide in Other Languages

• 请从以下网站获得该指南的简体中文版 https://

support.ruckuswireless.com

• Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

• このガイドの日本語版は https://support.ruckuswireless.com で

ご覧ください。

• 이 가이드의 한국어 버전은 웹 사이트 (https://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em https://

support.ruckuswireless.com.

• Puede ver la versión en español (América Latina) de esta guía

en https://support.ruckuswireless.com.

Before You Begin

Before deploying Ruckus products, please check for the latest

software and the release documentation.

• Release Notes and other user documentation are available at

http://support.ruckuswireless.com/documents.

• Software upgrades are available at http://

support.ruckuswireless.com/software.

• Softwar

e license and limited warranty information are

available at

http://support.ruckuswireless.com/warranty.

NOTE: The minimum software r

evision for the R650 is

SmartZone (SZ) 5.2 New AP Model.

Package Contents

A complete R650 installation package includes all of the following

items:

• R650 Access Point

• One wall-mount anchor kit, including two 1-inch No. 8 steel

pan-head Phillips sheet metal screws and wall-mount anchors

• One external T-bar bracket (two unassembled parts)

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Access Point Getting Started Guide

• AP Cloud Management Insert

• This Quick Setup Guide

Required Hardware Tools

• Admin PC (computer with an Ethernet port and Wi-Fi adapter)

• Cat 5e (or better) Ethernet cable

• Ruckus Wireless 48 VAC power adapter (sold separately) or

802.3at-compliant Power over Ethernet (PoE) switch or PoE

injector

Optional hardware and tools:

Customer-ordered Ruckus Wireless 902-0120-0000 secure

mounting bracket kit:

• If you are mounting the AP on a at surface using the secure

mounting bracket kit, then you need an electric drill with 4.75-

mm (3/16-in) drill bits.

• If you are mounting the AP on a pipe or pole using the secure

mounting bracket kit, then you will also need a 38.1-mm to

63.5-mm (1.5-in to 2.5-in) pipe or pole, customer-supplied two

pole clamps, and hand tools to tighten the clamps.

Step 1: Connecting Your Computer to the

1. Using an Ethernet cable, connect your computer network

port to the 2.5G ETH PoE port on the AP. Refer to Figure 2.

2. Connect the AC cable of the AC power adapter to a

convenient and protected power source. Connect the DC

output cable of the AC power adapter to the 48 VDC port on

the AP.

NOTE: Alternatively, connect the 2.5G ETH PoE port to a

PoE injector or switch for both po

wer and network

connectivity.

Alternatively, connect the computer and the AP with a basic

PoE switch in the following ways:

Connect the AP to a switch port.

b) Connect the computer to another switch port and

manually assign an IP address to congure the AP.

FIGURE 2 R650 AP Ports on Bottom Panel

TABLE 1 R650 AP Ports

No. Label Description

1 1G ETH 10/100/1000 Mbps port: RJ-45

Ethernet port (non-PoE)

2 2.5G

ETH PoE

100/1000/2500 Mbps PoE In Port:

RJ-45 Ethernet port (supports

802.3af/at PoE)

3 48V

0.75A

48 VDC input

4 USB USB Port

• Maximum Dimensions: 6 cm x 2

cm x 1.1 cm

• Interface: USB 2.0

• Connector: USB – Type-A plug

5 Reset

switch

Resets the AP

3. Verify that the PWR LED on the AP is lit a steady green.

Step 2: Preparing Y

our Computer for AP

Setup

NOTE: The following pr

ocedures assume Windows is the

operating system. Procedures for other operating systems are

similar.

1. On your Windows PC, navigate to Start > Control Panel >

Network and Sharing Center

> Change Adapter Settings

to congure your network adapter from the Local Area

Connection settings.

2. Navigate to Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties to edit the TCP/

IPv4 address settings.

The Internet Protocol Version 4 (TCP/IPv4) Properties

dialog box displays.

1 of 4

Published November 2019, Part Number 800-72206-001 Rev D

Summary of content (4 pages)

PAGE 1
• Software license and limited warranty information are available at http://support.ruckuswireless.com/warranty. FIGURE 2 R650 AP Ports on Bottom Panel NOTE: The minimum software revision for the R650 is SmartZone (SZ) 5.2 New AP Model. R650 Access Point Quick Setup Guide This Quick Setup Guide provides step-by-step instructions on how to install and begin using your Ruckus R650 dual-band 802.11ax indoor Wi-Fi access point (AP).
PAGE 2
IMPORTANT-QSG: Write down all of the currently active settings so you can restore your computer to its current configuration later (when this process is complete). 3. Select Use the following IP address (if it is not already selected) and make the following entries: • IP address: 192.168.0.22 (or any available address in the 192.168.0.x network, except 192.168.0.1) • Subnet mask: 255.255.255.0 • Default gateway: 192.168.0.1 Leave the DNS server fields empty. 4. Click OK to save your changes.
PAGE 3
FIGURE 4 Attaching the T-bar Bracket to the T-bar 4. Place the AP onto the mounting screws so the screw heads enter the keyholes on the AP enclosure, and push the AP down until the AP retainer tab snaps into place. R650 Caution Notices A caution calls your attention to a possible hazard that can damage equipment. CAUTION! The equipment can be connected to PoE networks without routing to the outside plant.