Ruckus Wireless™ ZoneFlex™ 7025 Multimedia Wi-Fi Wall Switch User Guide For the following ZoneFlex 7025 Multimedia Wi-Fi Wall Switch models: ■ 7025 Multimedia Wi-Fi Wall Switch (US) ■ 7025 Multimedia Wi-Fi Wall Switch (EU) Part Number 800-70273-001 Published December 2010 www.ruckuswireless.
Contents About This Guide Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii 1 Introducing the 7025 Multimedia Wi-Fi Wall Switch Overview of the 7025 Multimedia Wi-Fi Wall Switch . . . . . . . . . . .
Configuring the Multimedia Wi-Fi Wall Switch Configuring Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Configuring Internet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Default IP Addressing Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Obtaining and Assigning an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index iii
iv
About This Guide Document Conventions About This Guide This guide describes how to install, configure, and manage the Ruckus Wireless™ ZoneFlex™ 7025 Multimedia Wi-Fi Wall Switch. This guide is written for those responsible for installing and managing network equipment. Consequently, it assumes that the reader has basic working knowledge of local area networking, wireless networking, and wireless devices.
About This Guide Related Documentation Table 2.
About This Guide Documentation Feedback ■ Ruckus Wireless ZoneFlex 7025 Multimedia Wi-Fi Wall Switch User Guide ■ Part number: 800-70273-001 ■ Page 88 NOTE: Throughout this guide, the ZoneFlex 7025 Multimedia Wi-Fi Wall Switch may be referred to as “ZF7025,” “Access Point,” “AP” or simply, “device.” All of these terms are synonymous for the purposes of this guide.
About This Guide Documentation Feedback iv
1 Introducing the 7025 Multimedia Wi-Fi Wall Switch In This Chapter Overview of the 7025 Multimedia Wi-Fi Wall Switch . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the ZoneFlex 7025 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting to Know the ZoneFlex 7025 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introducing the 7025 Multimedia Wi-Fi Wall Switch Overview of the 7025 Multimedia Wi-Fi Wall Switch Overview of the 7025 Multimedia Wi-Fi Wall Switch Congratulations on your purchase of the Ruckus Wireless ZoneFlex 7025 Multimedia Wi-Fi Wall Switch! The ZoneFlex 7025 Multimedia Wi-Fi Wall Switch is the industry’s first wired and wireless wall switch that integrates high-speed 802.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Unpacking the ZoneFlex 7025 Unpacking the ZoneFlex 7025 1. Open the ZoneFlex 7025 package, and then carefully remove the contents. 2. Return all packing materials to the shipping box, and put the box away in a dry location. 3. Verify that all items listed in Package Contents below are included in the package. Check each item for damage. If any item is damaged or missing, notify your authorized Ruckus Wireless sales representative.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features Figure 1. ZF7025-US front view 5 1 2 3 4 Table 3. ZF7025-US front view Number Name Description 1 Pass Through port Pass through port. 2 Power Input Optional 48V DC power input. 3 LAN1-LAN3 Three 10/100 RJ-45 LAN ports. 4 LAN4 One 10/100 RJ-45 LAN port with PoE out. Supports 802.3af PSE Class 0/2 (depending on power input). 5 Reset Buttons (left Refer to “Reset Buttons” on page 9 for details.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features Figure 2. ZF7025-US rear panel 1 2 3 4 Table 4. ZF7025-US rear panel features Number Name Description 1 PoE In LAN 5/Uplink Uplink LAN port that supports 802.3af and 802.3at Power over Ethernet (PoE) input. 2 Punch down Block 110 punchdown block. 3 Pass Through Port RJ-45 pass through port for the pass through connection. 4 LEDs See Table 7 for LED descriptions and behaviors.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features ZF7025-EU Model This section describes the physical features of the ZF7025-US model, which is designed to fit in a standard EU-style wall electrical outlet box. The outlet box must conform to BS 4662, with a minimum depth of 35mm. Front View Features Figure 3 shows the front view of the ZF7025-EU model. For a description of each front view element, refer to Table 5. Figure 3.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features Rear View Features Figure 4 shows the rear panel of the ZF7025-EU model. For a description of each rear panel element, refer to Table 7. Figure 4. ZF7025-EU rear panel 1 2 4 Table 6. 3 ZF7025-EU rear panel features Number Name Description 1 PoE In LAN 5/Uplink Uplink LAN port that supports 802.3af and 802.3at Power over Ethernet (PoE) input. 2 Punch down Block 110 punchdown block.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features LEDs The LEDs for both the US and EU models are the same. Refer to Table 7 for descriptions of LEDs and their behaviors. The LEDs are not visible once the AP is installed. Table 7. ZF7025 LEDs LED Meaning WLAN Green: WLAN service is available. Off: No WLAN service available. OPT Not used in this model. DIR Green: AP is being managed by ZoneDirector. Off: AP is not being managed by ZoneDirector.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features Reset Buttons Two reset buttons on the left side of the AP are used to reboot or factory reset the AP. Figure 5. Reset buttons Hard Reset button Soft Reset button Press and release either of the reset buttons to reboot the AP. Press and hold the Hard Reset button for three seconds or more to reset the AP to factory defaults.
Introducing the 7025 Multimedia Wi-Fi Wall Switch Getting to Know the ZoneFlex 7025 Features 10
2 Installing the Multimedia Wi-Fi Wall Switch In This Chapter Installing the ZF7025 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Associate a Wireless Client with the Access Point . . . . . . . . . . . . . . . . . . . . . . . . 18 Physical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 Installing the ZF7025 Before starting with the installation, make sure that you have the following items that are required for the installation ready: ■ A computer with a Web browser ■ Two CAT5 Ethernet cables ■ An IEEE 802.3af/at-compliant PoE switch or PoE injector and power adapter Step 1: Prepare the Administrative Computer The administrative computer is the computer that you will be using to access the device’s Web interface.
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 You can leave the Alternate DNS server box blank. 8. Click OK to save your changes and close the TCP/IP Properties dialog box. 9. Click OK again to close the Local Area Connection Properties dialog box. Windows saves the IP address settings that you have configured. Figure 6. Sample configuration in the TCP/IP Properties dialog box Step 2: Connect the Device to a Power Source and the Admin Computer 1. Connect the AP to an 802.3af or 802.
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 3. Take one of the CAT5 Ethernet cables. Connect one end of the Ethernet cable to the Ethernet port on your computer, and then connect the other end to the 10/ 100 DATA IN port on the PoE injector. 4. Take the other Ethernet cable. Connect one end to the PoE OUT port on the PoE injector, and then connect the other end to the PoE In LAN 5/Uplink port on the rear of the device (see Figure 8). Figure 8.
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 Figure 9. Web interface login page 4. Click the Login button. The Status :: Device page appears. 5. Continue to “Step 4: Configure the Wireless Settings”. Step 4: Configure the Wireless Settings To complete this step, you will need to configure the settings on the Common tab and at least one Wireless # tab. These are the essential wireless settings that will enable wireless devices on the network to associate with the Access Point.
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 2. Verify that the common wireless settings are configured as listed in Table 10. Table 10. Common wireless configuration Setting Recommended Value Wireless Mode 2.4GHz (802.11b/g/n) (not configurable). Channel SmartSelect Channel Width 20MHz Country Code • If you purchased the Access Point in the United States, this value is fixed to United States at the factory and is not user configurable.
Installing the Multimedia Wi-Fi Wall Switch Installing the ZF7025 Configure Wireless # Settings 1. Click one of the Wireless # tabs. 2. In Wireless Availability, click Enabled. 3. In Broadcast SSID, click Enabled. 4. Clear the SSID box, and then type a unique and descriptive name that you want to call this wireless network. For example, you can type Ruckus Wireless AP. This SSID is the name that will help users identify this wireless network in their wireless network connection application.
Installing the Multimedia Wi-Fi Wall Switch Physical Installation Associate a Wireless Client with the Access Point 1. On the administrative computer, verify that the wireless interface is enabled. On Windows XP, click All Programs > Connect To > Wireless Network Connection to enable the wireless interface. 2. In the system tray, right-click the (Wireless Network Connection) icon, and then click View Available Wireless Networks. 3.
Installing the Multimedia Wi-Fi Wall Switch Physical Installation • If required, connect the cable providing support for pass-through devices to the Pass Through port. 3. Mount the ZoneFlex 7025. • • • Align the mounting bracket with the outlet box so that the two screw holes line up, and pull the Ethernet cable through the center of the mounting bracket. Affix the mounting bracket to the outlet box using the two mounting screws provided.
Installing the Multimedia Wi-Fi Wall Switch Physical Installation Figure 13. Punch-down block wiring White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown Congratulations! Your wireless network is now active and ready for use. ■ ■ ■ If you want to become familiar with the Multimedia Wi-Fi Wall Switch Web interface, refer to “Navigating the Web Interface” on page 21.
3 Navigating the Web Interface In This Chapter Logging Into the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Navigating the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating the Web Interface Logging Into the Web Interface Logging Into the Web Interface If you need to manage the device, you do it with the features of the Ruckus Wireless Web interface (which you already used to set up the device for use). NOTE: The following procedure assumes that you know the IP address that the device is currently using, or you have some means of determining the dynamic IP address in use by the device.
Navigating the Web Interface Navigating the Web Interface Navigating the Web Interface You manage the Multimedia Wi-Fi Wall Switch through a Web browser-based interface that you can access from any computer that is on the same subnet as the Multimedia Wi-Fi Wall Switch. Table 11 lists the Web interface features that are identified in Figure 15. Figure 15. Elements of the 7025 Multimedia Wi-Fi Wall Switch Web Interface Log Out Button Tabs Help Button Menu Workspace Table 11.
Navigating the Web Interface Navigating the Web Interface Table 11. 7025 Multimedia Wi-Fi Wall Switch Web interface elements Element Description Logout Button Click this button to log out of the Multimedia WiFi Wall Switch. Help Button Click this button to open a help window with information related specifically to the options currently displayed in the workspace.
4 Configuring the Multimedia Wi-Fi Wall Switch In This Chapter Configuring Device Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Configuring Internet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Configuring Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Controlling Access to the Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Multimedia Wi-Fi Wall Switch Configuring Device Settings Configuring Device Settings Device settings refer to the device name and service provider login settings. Figure 16. The Configuration :: Device page To configure the device settings 1. Go to Configuration > Device. The Configuration :: Device page appears. 2. In Device Name, type a new name for the device or leave as is to accept the default device name (RuckusAP).
Configuring the Multimedia Wi-Fi Wall Switch Configuring Internet Settings Configuring Internet Settings Internet settings define how the Multimedia Wi-Fi Wall Switch connects to your local area network and to the Internet. This section describes how to view and configure the Multimedia Wi-Fi Wall Switch’s Internet settings.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Internet Settings Figure 17. The Configuration :: Internet page To assign a static IP address to the AP 1. Go to Configuration > Internet. The Internet page appears. 2. Verify that Connection Type is set to Static IP. 3. When the Static IP options appear, you can changes to the following settings: • • • • Gateway: This is the gateway IP address of the Internet interface.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Internet Settings Changing the Network Connection Type To change the connection type (DHCP or Static IP) 1. Go to Configuration > Internet. The Configuration > Internet page appears. 2. In Connection Type, select DHCP or Static IP. 3. If you selected Static IP, fill in the related fields according to your network configuration: • • • • Gateway: This is the gateway IP address of the Internet interface.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Internet Settings To renew or release the DHCP server-assigned IP address 1. Go to Status > Internet. 2. Review the current settings. 3. If the current Connection Type is DHCP, you will be able to see the currentlyassigned IP address and subnet mask listed below. • • To force the DHCP server to assign a new IP address to the Multimedia Wi-Fi Wall Switch, click Renew DHCP.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Configuring Wireless Settings This section describes how to configure the wireless settings of the ZF7025 Multimedia Wi-Fi Wall Switch. There are two types of wireless settings that you need to configure: ■ ■ Configuring Common Wireless Settings: Includes the wireless mode, country code, and advanced wireless settings, such as the wireless transmit power and wireless protection mode.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings To configure the wireless settings common to all WLANs 1. Go to Configuration > Wireless. The Configuration :: Wireless :: Common page appears. 2. Make changes to the common wireless settings listed in the table below. Table 12. Common Wireless settings Setting Description Wireless Mode Only one wireless mode is available on the ZF7025: • 2.4GHz (802.11b/g/n): This setting allows 802.11b, 802.11g, and 802.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings 3. If you are using AeroScout Tags in your organization to locate assets or personnel, you can use your ZoneFlex AP to relay location or presence data from the AeroScout Tags to the AeroScout Engine via Wi-Fi. To enable the AP to relay AeroScout data, click the Enable option in AeroScoutRFID tag detection.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Figure 20. The Configuration :: Wireless :: Advanced :: Common page To configure the advanced common options 1. On the Configuration > Wireless page, click Edit Common Settings. The Configuration :: Wireless :: Advanced :: Common page appears.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings 2. Configure the advanced settings listed in Table 13 as required. Table 13. Advanced > Common options Option Description Transmit Power The default setting is Full. Select the level of transmit power from the drop-down menu. This option sets the maximum transmit power level relative to the predefined power (this value differs according to the current country code). Protection Mode (Inactive by default.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Configuring Wireless # Settings The ZF7025 provides up to eight wireless LANs that can be individually configured to provide different kinds of services for different kinds of wireless clients, traffic types or different user groups. Each WLAN can be configured with separate security settings, VLANs, access controls and rate limiting policies, among other settings. Figure 21. Wireless # settings To configure wireless settings 1.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Table 14. Wireless [#] options SSID This is the publicly-broadcast “name” of your wireless network. SSIDs can contain up to 32 alphanumeric characters and are case-sensitive. Dynamic VLAN This allows the RADIUS server to indicate the virtual LAN assignment of a wireless client during the 802.1X authentication process.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Using WEP CAUTION: WEP encryption has been proven to be easily circumvented. Therefore, Ruckus Wireless recommends using WPA whenever possible, and only use WEP if your client devices do not support WPA. CAUTION: Do not customize these options unless you are an experienced network administrator or are under the guidance of an IT/support professional. Figure 22. WEP settings To configure WLAN-specific WEP encryption settings 1.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings 4. Review the encryption settings listed in Table 15, and then make changes as required. Table 15. WEP settings Encryption Setting Description Authentication Mode Your options include: • Open: No security measure is enforced. • Shared Key: The selected Default Shared Key is used. • Auto: Automatically-selected authentication mode. Encryption Strength • 64 bit: Specify the key with 10 hexadecimal digits or 5 ASCII characters.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Using WPA Use of WPA-PSK allows automatic key generation based on a single passphrase. WPAPSK provides very strong security, but may not be supported on older wireless devices. In some cases, the older devices can be upgraded with adapters to take advantage of WPA-PSK.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings 4. Review the encryption settings listed in Table 16, and then make changes as preferred. Table 16. WPA settings Encryption Setting Description WPA Version Your options are WPA, WPA2 or WPA Auto. • When WPA is selected, the wireless client decides which version of WPA will be used. WPA is the recommended default for best compatibility. Wi-Fi WPA-capable PDAs and other devices are usually limited to WPA + TKIP.
Configuring the Multimedia Wi-Fi Wall Switch Configuring Wireless Settings Customizing 802.1X Settings CAUTION: Do not customize these options unless you are an experienced network administrator or are under the guidance of an IT/support professional. If you choose WPA as the encryption method, you have the option to set up the Multimedia Wi-Fi Wall Switch to act as an 802.1X proxy, utilizing external authentication sources such as a RADIUS server.
Configuring the Multimedia Wi-Fi Wall Switch Setting Threshold Options • • • RADIUS NAS-ID: Enter the network ID assigned to your RADIUS server. Authentication Server [-Required-]: Enter the information needed to establish a connection between the Multimedia Wi-Fi Wall Switch and the RADIUS server. Accounting Server [-Optional-]: Enter the information needed to establish this connection. 6. Click Update Settings to save and apply the changes. A confirmation message appears at the top of this page. 7.
Configuring the Multimedia Wi-Fi Wall Switch Setting Threshold Options 4. Review the options listed in Table 17, and then make any needed changes. Table 17. Threhold options Option Description Beacon Interval (The default value is 100.) The value indicates the frequency interval of the beacon in milliseconds. A beacon is a broadcast packet sent by the AP to synchronize the wireless network. Data Beacon Rate (The default value is 10.
Configuring the Multimedia Wi-Fi Wall Switch Rate Limiting Figure 25. Threshold settings Rate Limiting Rate Limiting allows you to cap the data transfer rates per client for a specific WLAN. To enable per station rate limits 1. Go to Configuration > Wireless. 2. Select the WLAN that you want to configure from the tabs at the top of the page. 3. Click the Edit Settings button next to Rate Limiting. The Rate Limiting page appears. 4.
Configuring the Multimedia Wi-Fi Wall Switch Controlling Access to the Wireless Network Figure 26. Limit per station traffic rates on a specific WLAN Controlling Access to the Wireless Network Access Control enables you to specify the stations are allowed to join (associate with) your WLAN networks. Access controls can be configured for each WLAN from its respective Wireless # tab. Access Control Options This section describes the options that you can use to control access to the wireless network.
Configuring the Multimedia Wi-Fi Wall Switch Controlling Access to the Wireless Network ■ Denying Only Stations Listed in the Access Controls Table: If you select Deny only stations listed in the Access Controls Table, then stations entered into the access-controls table are disallowed but all others are allowed. To add MAC addresses, see “Changing the Access Controls for a WLAN” on page 47.
Configuring the Multimedia Wi-Fi Wall Switch Configuring LAN Ports • Address: Six text boxes appear in which you enter the desired MAC address, in hexadecimal digit form, two characters in each box. You can specify a full 12-hex-digit MAC address or enter “wildcard” characters for “don't care” digits. Allowable hex-digit characters are 0-9, a-f, and A-F.
Configuring the Multimedia Wi-Fi Wall Switch Configuring LAN Ports Figure 28. The Configuration :: LAN Ports page To configure LAN ports 1. Go to Configuration > LAN Ports. 2. Review the following table and make changes as needed for each of the ports labeled LAN 1 through LAN 4, which correspond to the labels on the outside of the AP. Table 18. Configure the LAN ports Setting Description Enable All LAN ports are enabled by default. Unchecking this box next to a port disables that LAN port entirely.
Configuring the Multimedia Wi-Fi Wall Switch Configuring LAN Ports Working with Port-Based VLANs The ZoneFlex 7025 Multimedia Wi-Fi Wall Switch provides options for segmenting all incoming traffic (both wireless and wired Ethernet traffic) into specific VLANs. There are three ways to segment incoming traffic into VLANs: ■ ■ ■ Each of the eight wireless interfaces (SSIDs) can be configured with a specific VLAN ID: (Configuration > Wireless > Wireless [#] > VLAN).
5 Managing the Multimedia Wi-Fi Wall Switch In This Chapter Viewing Current Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Changing the Administrative Login Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Configuring Management Access Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Sending a Copy of the Log File to Ruckus Wireless Support . . . . . . . . . . . . . . .
Managing the Multimedia Wi-Fi Wall Switch Viewing Current Wireless Settings Viewing Current Wireless Settings If you want to view the current common wireless settings that the Multimedia Wi-Fi Wall Switch is using, go to the Status > Wireless page. Table 19 lists the descriptions of each common wireless setting. Figure 29.
Managing the Multimedia Wi-Fi Wall Switch Changing the Administrative Login Settings Table 19. Common Wireless settings Setting Description Wireless Mode Shows the wireless mode that the Multimedia WiFi Wall Switch is currently using. Possible values include: • 11n/g Channel Shows the wireless channel that the Multimedia Wi-Fi Wall Switch is currently using. If you set the wireless channel to SmartSelect, this field will show the value Channel # [SmartSelect].
Managing the Multimedia Wi-Fi Wall Switch Changing the Administrative Login Settings 3. Under Service Provider Login, change the default administrator login settings. • • • (Optional) In Username, type a new user name that you will use to log in to the Web interface. The default user name is super. In Password, type a new password to replace the default password sp-admin. In Password Confirmation, retype the new password. 4. Click Update Settings. The message Your parameters were saved appears.
Managing the Multimedia Wi-Fi Wall Switch Configuring Management Access Options Configuring Management Access Options In addition to managing the Multimedia Wi-Fi Wall Switch via a Web browser through HTTP, several other management access options are available on the AP. These options include management access via HTTPS, Telnet, and SSH. You can also enable remote management, if you want to be able to access the Multimedia Wi-Fi Wall Switch Web interface from outside your local network. Figure 31.
Managing the Multimedia Wi-Fi Wall Switch Configuring Management Access Options 2. Review the access options listed in Table 20, and then make changes as needed. Table 20. Management Access Options Option Description Telnet access By default, this option is disabled (inactive). Telnet port This field lists the default Telnet port of 23. You can manually change this port number, if required. SSH access By default, this option is enabled (active).
Managing the Multimedia Wi-Fi Wall Switch Enabling Logging and Sending Event Logs to a Syslog Server Enabling Logging and Sending Event Logs to a Syslog Server If you have a syslog server on the network, you can configure the Multimedia Wi-Fi Wall Switch to send the device logs to the server. You will need to enable logging, and then configure the ZF7025 to send logs to the syslog server. 1. Go to Administration > Log. The Administration :: Log page appears. 2. Look for Log Status, and then click Enabled.
Managing the Multimedia Wi-Fi Wall Switch Sending a Copy of the Log File to Ruckus Wireless Support Sending a Copy of the Log File to Ruckus Wireless Support The Support Info log consists of the configuration and run-time status of the Multimedia Wi-Fi Wall Switch and can be useful for troubleshooting.
Managing the Multimedia Wi-Fi Wall Switch Upgrading the Firmware Upgrading the Firmware You can use the Web interface to check for software updates/upgrades for the firmware built into the Multimedia Wi-Fi Wall Switch. You can then apply these updates to the device in one of two ways: ■ Manually updating on an as-needed basis, or; ■ Automating the update by setting an update schedule.
Managing the Multimedia Wi-Fi Wall Switch Upgrading the Firmware 2. Click the host name field, and then type the URL of the server. Or click the IP address field, and then type the IP address of the server. CAUTION: Do not change any of the Image Control File, Username, or Password entries. 3. Click Perform Upgrade. A status bar appears during the upgrade process. 4. After the upgrade is completed, you must manually reboot the Multimedia Wi-Fi Wall Switch. Upgrading Manually via the Web 1.
Managing the Multimedia Wi-Fi Wall Switch Upgrading the Firmware Figure 34. The Auto Upgrade section on the Upgrade page To configure automatic upgrades 1. In the Upgrade Method options, click the button for your preferred upgrade method. NOTE: Automatic Upgrade is only available if you select TFTP, FTP, or Web as the Upgrade Method. 2.
Managing the Multimedia Wi-Fi Wall Switch Upgrading the Firmware 5. In Schedule Reboot Time after Upgrade, select the time (GMT) when the Multimedia Wi-Fi Wall Switch will be rebooted automatically after the new firmware is downloaded. The Multimedia Wi-Fi Wall Switch requires a reboot to complete the upgrade process. Ruckus Wireless recommends that you select an offpeak hour so fewer users would be affected by the reboot. 6.
Managing the Multimedia Wi-Fi Wall Switch Rebooting the Multimedia Wi-Fi Wall Switch Rebooting the Multimedia Wi-Fi Wall Switch You can use the Web User interface to prompt the Multimedia Wi-Fi Wall Switch to reboot, which simply restarts the Multimedia Wi-Fi Wall Switch without changing any of the current settings. CAUTION: Rebooting the Multimedia Wi-Fi Wall Switch will disrupt network communications on any currently active WLANs. Figure 35.
Managing the Multimedia Wi-Fi Wall Switch Resetting to Factory Defaults Resetting to Factory Defaults WARNING: DO NOT reset the Multimedia Wi-Fi Wall Switch to factory defaults, unless you are directed to do so by Ruckus Wireless support staff or by a network administrator. Do this only if you are able to immediately reconnect the restored Multimedia Wi-Fi Wall Switch to your computer, to reconfigure it for Wi-Fi network use.
Managing the Multimedia Wi-Fi Wall Switch Running Diagnostics Figure 36. Pinging ruckuswireless.com Figure 37. Running traceroute on ruckuswireless.
Managing the Multimedia Wi-Fi Wall Switch Where to Find More Information Where to Find More Information If you have questions that this User Guide does not address, visit the Ruckus Wireless Support Portal at http://support.ruckuswireless.com/. The Support Portal hosts the latest versions of user documentation. You can also find answers to frequently asked questions (FAQs) for each Ruckus Wireless product type.
Index Numerics F 802.1X, 42 802.
PING, 64 PoE injector, 13 port-based VLAN, 48, 50 protection mode, 35 punch down block, 5, 7, 19 R rebooting, 9, 63 releasing DHCP, 29 renewing DHCP, 29 reset buttons, 9 S SSID, 37 static IP, 29 static IP address, 27 syslog, 57 syslog server, 57 wireless security 802.
