User's Guide

FIGURE 6 Attaching the mounting br
acket to a vertical
pole
4. Continue with Mounting the Linkage Br
acket to the U-Joint
Bracket on page 3.
Mounting the Linkage Bracket to the U-Joint
Bracket
1. The linkage bracket attaches to the U-joint bracket using an
M8 bolt and washer set. The linkage bracket is symmetrical,
and either end can be attached to the U-joint bracket.
NOTE: Mak
e sure that linkage bracket is installed with its
serrated external-tooth lock washer on the inside of the
U-joint bracket anges. This ensures that the azimuth
adjustment does not change.
2. Loosely assemble the linkage bracket (1), the U-joint bracket
(3), one serr
ated external-tooth lock washer (2), and one M8
bolt and washer set (4).
FIGURE 7 Attaching the linkage bracket to the U-joint
bracket
1. Linkage bracket
2.
U-joint braket
3. External-tooth lock
washer
4. M8 bolt
3. Set the azimuth required by the AP.
4. Tighten the M8 bolt to 13.6 N.m (120 in-lbs).
5. Continue with Attaching the AP Bracket to the Linkage
Bracket on page 3.
Attaching the AP Bracket to the Linkage
Bracket
Attach the AP bracket to the linkage bracket using the included
bolt, lock washer, at washer, serrated external-tooth washer
and nut shown in the illustration below.
The linkage bracket is symmetrical, and either end can be
attached to the AP bracket.
Loosely assemble the AP bracket to the linkage bracket using the
M8 bolt, washer and nut set.
FIGURE 8 Attach the linkage bracket to the AP bracket
NOTE: Mak
e sure that the linkage bracket is installed with its
serrated external-tooth lock washer on the inside of the AP
bracket anges. This ensures that the elevation adjustment
does not change.
Attaching the AP Bracket to the Access Point
1. Place the AP bracket onto the back side of the AP so that the
four larger screw holes on the bracket align with the four
screw holes on the AP.
FIGURE 9 Attaching the AP br
acket to the AP
2. Use four 0.5-inch x 0.250-28 hex bolts with split lock and at
washer sets to mount the AP br
acket to the AP. Tighten the
bolts to 2.5-3.0 N.m (22-27 in-lbs).
CAUTION! Mak
e sure that the screws are no longer than
0.5 inch. If a screw is longer than 0.5 inch, it can damage
the AP chassis.
NOTE: This kit may include e
xtra screws, nuts and
washers. You may use the extras where required.
3. Continue with Set the Ele
vation and Tighten the Elevation
Bolt on page 3.
Set the Elevation and Tighten the Elevation
Bolt
1. Set the elevation required by the AP.
2. Tighten the M8 bolt to 13.6 N.m (120 in-lbs).
3. Continue with Powering the AP with AC on page 3.
Powering the AP with AC
1. Separate the AC cable connector parts by unscrewing the
boot from the cable gland and the cable gland from the
connector housing..
2. Feed the end of the AC cable through the boot and cable
gland.
3. Strip the AC cable as shown.
4. Insert the stripped part of the conductors into the
appropriate terminals on the connector housing. The
conductors are color coded and must be connected to the
appropriate terminals as shown in gure below.
NOTE: The color coding of wir
e conductors varies by
region. Before completing this step, check your local
wiring standards for guidance.
Copyright
©
2019 CommScope, Inc. All rights r
eserved. Page 3 of 4
Published December 2019, Part Number 800-72101-001 Rev C