Instruction Manual

Wall Mounting Kit Installation Instructions
FX5/FX6/FE2 Electric Heaters
Part No. 9841 Rev.3.02
WARNING
WARNING. If the heater is installed on a structure that is to be transported, provide additional
support for the heater during transit. The suspended weight should not exceed 250 lbs (114
kg). Refer to the unit heater owner's manual for the mounting specications and conditions.
Check that your heater model number corresponds to the model number shown on the mounting kit carton (see Table 2).
Step 1
Fasten Z-Sections (#1) to a surface or structure that will support the heater's
weight using the installer supplied fasteners.
ote: N Installer to supply four 3/8" diameter, grade 5 bolts or equivalent strength
fasteners.
Step 2
Bolt the Arm Assembly (#2) to the Z-Section (#1) using 3/8"-16 UNC X 1" Bolts (#5),
Locking Washers (#8) and 3/8"-16 UNC Nuts (#11).
Step 3
Bolt Mounting Bracket Attach Assembly (#3) to the heater's top panel
using two 1/2"-13 UNC Bolts (#4), Nuts (#10), Flat Washers (#12) and
1/2" Locking Washers (#7).
ote: N Mounting Attach Assembly Bracket (#3) must be placed with the
threaded hole closest to the control enclosure side of the heater,
attach to heater using the rear two holes on top panel.
Step 4
Lift the heater into place and fasten it to the Arm Assembly (#2) using a
5/8"-11 UNC X 1 1/4" Bolt (#6) and 5/8" Locking Washer (#9).
Table 1 – Contents
Item Qty Description Part No.
1 2 Angle, wall mounting kit support 3152
2 1 Arm, mounting 9706
3 1 Mounting Bracket Attach Assembly
12" - 9675
16" - 9676
20" - 9677
4 2 Bolt 1/2-13UNC x 1 1/4 long, hexagon head 2940
5 4 Bolt 3/8-16UNC x 1 1/4 long, hexagon head 3153
6 1 Bolt 5/8-11UNC x 1 1/4 long, hexagon head 3122
7 2 Lockwasher 1/2" ID split 4373
8 4 Lockwasher 3/8" ID split 3159
9 1 Lockwasher 5/8" ID split 3093
10 2 Nut 1/2-13 UNC hexagonal 4372
11 4 Nut 3/8-16 UNC hexagonal 2785
12 2 Washer, flat 1/2" 2941
Table 2 – Wall Mounting Kit
FX5/FX6/FE2 Heater Cabinet Size Part No.
12" 9730
16" 9731
20" 9732
CAUTION
CAUTION. This step will require more than one person due
to the weight of the heater. Refer to the unit heater owner's
manual for the weight of the heater.
9
4
3
Control enclosure
7 1/4"
(184.8 mm)
center to
center
6
11
8
1
2
4
Heater swivel point
Mounting surface to center of swivel point
31 5/8"
(803.5 mm)
5
7/16" hole size
recommended
mounting holes
(4 per z-section)
ø
12 1/16"
(306 mm)
17 15/16"
(456 mm)
Supplied by customer, (qty:
4) 3/8", grade 5 bolts or
equivalent strength fasteners
(not shown for clarity)
7
10
12