THREAD CUTTING TOOLS
30 020 230 520 142 800 M 3 - M 20 230 030 Li 230 200 Li 142 1000 M 2 - M 24 230 020 E 230 240 E 142 800 MF 3 - MF 52 235 030 235 520 144 800 G 1/8 - G 2" 236 018 236 020 146 800 1/16 - 2" 246 116 246 020 147 800 Nr. 2 - 2" 246 020 UNC 246 200 UNC 148 800 Nr.
Steel (N/mm2) < 1000 Steel (N/mm2) < 1200 < 800 N/mm² <1000 N/mm² <1200 N/mm² Main application Other application Titanium alloyed Cast iron Plastics Bronze Brass Aluminium Stainless steel Steel (N/mm2) < 800 06 141
M 60° ISO 2 6H 4 Ø1 Set: Taper tap: Second tap: Final tap: Thread: Flanks: L2 Hand taps M DIN 352 HSS, HSS-left-handed thread and HSSE-Co 5 ground Also available individually Taper tap: Article no. 230 ......-1 Second tap: Article no. 230 ......-2 Final tap: Article no. 230 ......-3 3-piece 6 - 8-thread chamfer 4 - 5-thread chamfer 2 - 3-thread chamfer metric, DIN ISO 13 relief-ground L1 06 DIN 352 HSS HSSE Co 5 Packing unit: set in plastic pack 800 HSS 230 ... N/mm² 800 HSS 230 ...
22568 B ISO 2 6g 06 60° Ø1 DIN EN HSS HSSE Co 5 Round dies M DIN EN 22568 HSS, HSS-left-handed thread and HSSE-Co 5 ground T Type: Type B closed – solid die Thread: metric, DIN ISO 13 Packing unit: in plastic tubes of 1 N/mm² 800 HSS 237 ... Li N/mm² 1000 HSSE Co 5 237 ... E N/mm² Nominal thread size M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M 237 ... 238 ...
HSS MF 4 60° ISO 2 6H Ø1 Set: Taper tap: Final tap: Thread: Flanks: L2 Hand taps MF DIN 2181 HSS, ground 2-piece 5 - 6-thread chamfer 2 - 3-thread chamfer metric, fine, DIN ISO 13 relief-ground L1 06 DIN 800 2181 N/mm² After two rotations of the drill turn back 1/3 rotation to break the chip. Thus the strain on the screw tap decreases. Lubrication with RUKO cutting oil is recommended.
22568 800 N/mm² B ISO 2 6g 06 60° Ø2 DIN EN HSS Round dies MF DIN EN 22568 HSS, ground Type: Type B closed – solid die Thread: metric fine, DIN ISO 13 T It is recommended that the threading dies are turned back briefly now and then so that the chips break and do not clog the threads. Lubrication with RUKO cutting oil is recommended.
HSS Rp (BSP) G/Rp DIN 800 5157 N/mm² 4 55° ISO 2 6H Ø1 2-piece 5 - 6-thread chamfer 2 - 3-thread chamfer DIN ISO 228 "G" (cylindrical pipe thread) DIN 2999 "Rp" (Whitworth pipe thread) relief-ground Flanks: L1 Set: Taper tap: Final tap: Thread: L2 Hand taps G DIN 5157 HSS, ground Packing unit: set in plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Nominal thread size G / Rp G 1/8 G 1/4 G 3/8 G 1/2
BSW Ww DIN 800 (BSW) 352 N/mm² HSS Ø1 4 55° 3-piece 5 - 6-thread chamfer 4 - 5-thread chamfer 2 - 3-thread chamfer BSW, formerly DIN 11 relief-ground L1 Set: Taper tap: Second tap: Final tap: Thread: Flanks: L2 Hand taps BSW ≈ DIN 352 HSS, ground 06 Packing unit: set in plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Also available individually Taper tap: Article no. 246 ......-1 Second tap: Article no. 246 ......-2 Final tap: Article no. 246 ......
UNC HSS UNC 2B 4 60° Ø1 3-piece 5 - 6-thread chamfer 4 - 5-thread chamfer 2 - 3-thread chamfer American UNC coarse thread relief-ground L1 Set: Taper tap: Second tap: Final tap: Thread: Flanks: L2 Hand taps UNC ≈ DIN 352 HSS, ground Packing unit: set in plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Also available individually Taper tap: Article no. 246 ...... UNC1 Second tap: Article no. 246 ...... UNC2 Final tap: Article no. 246 ......
UNF HSS DIN 800 2181 N/mm² UNF 2B 4 60° Ø1 2-piece 5 - 6-thread chamfer 2 - 3-thread chamfer American UNF fine thread relief-ground L1 Set: Taper tap: Final tap: Thread: Flanks: L2 Hand taps UNF ≈ DIN 2181 HSS, ground 06 Packing unit: set in plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Nominal thread size UNF Threads per inch Thread core hole Ø1 mm L1 mm L2 mm HSS Nr. 2 Nr. 3 Nr. 4 Nr. 5 Nr.
DIN 352 HSS HSSE Co 5 60° 4 ISO 2 6H Hand tap sets HSS and HSSE-Co 5 in steel case 245 001 245 001 E 22- piece set of hand taps M DIN 352 one three-piece set each of M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 + 1 tap wrench DIN 1814 size 1 1/2 245 002 245 002 E 29- piece set of hand taps DIN 352 one three-piece set each of M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 + 7 twist drills DIN 338 Type N Ø 2,5 - 3,3 - 4,2 - 5,0 - 6,8 - 8,5 - 10,2 mm + 1 tap wrench DIN 1814 size 1 1/2 245 003 245 003 E 2
HSS HSSE Co 5 DIN 352 60° 4 ISO 2 6H 06 Thread-cutting sets HSS and HSSE-Co 5 in steel case HSS HSSE Co 5 31- piece set of DIY thread-cutting tools one three-piece set each of hand taps M DIN 352 M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 + 7 dies Ø 25,0 mm ≈ DIN EN 22568 in each of the sizes M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 + 1 die stock 25,0 x 9,0 mm DIN 225 + 1 tap wrench, size 1½ DIN 1814 + 1 screwdriver 245 010 245 010 E 37- piece set of thread-cutting tools one three-piece set each
B DIN 352 M 60° ISO 2 6H 4 Ø1 L2 Single-cut taps M ≈ DIN 352 HSS and HSSE-Co 5 ground Thread: metric, DIN ISO 13 Flanks: relief-ground L1 The single-cut tap HSS for through threads in unalloyed and low-alloyed steels up to a strength of 800 N/mm². The single-cut tap HSSE-Co 5 for through threads in unalloyed and alloyed steels up to a strength of 1000 N/mm², malleable cast iron and non-ferrous metals. The thread can be cut in one operation by hand or machine.
C NPT HSS NPT 800 N/mm² Ø1 4 55° American conical pipe thread to ANSI B.1.20.1 relief-ground 1:16 L1 Thread: Flanks: Cone: L2 Single-cut taps NPT HSS, ground 06 For through threads in unalloyed or low-alloyed steels up to 800 N/mm² strength, malleable cast iron and non-ferrous metals. The thread can be cut in one operation by hand or machine.
G HSS Rp (BSP) B DIN 800 5157 N/mm² 55° 4 ISO 2 6H Single-cut taps G ≈ DIN 5157 HSS, ground G/Rp Ø1 L2 Thread: DIN ISO 228 "G" (cylindrical pipe thread) DIN 2999 "Rp" (Whitworth pipe thread) Flanks: relief-ground L1 Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Nominal thread size G / Rp G 1/8 G 1/4 G 3/8 G 1/2 G 3/4 G 1" Thread core hole Ø1 mm L1 mm L2 mm HSS 28 19 1
Extension sleeves DIN 377 06 As extension for hand thread-cutting tools. Inside and outside square of identical size.
Die stocks as per DIN 225 For closed and slotted taps as per DIN EN 24231. With steel handles one of which can be unscrewed and five screws for clamping the tap.
Adjustable tap wrenches as per DIN 1814 06 Ideal for thread-cutting in inaccessible places. With two-jaw chuck for tensioning square shanks. With steel handles one of which can be unscrewed.
158 Page HSSE Co 5 Article no.
Main application Other application Titanium alloyed Cast iron Plastics Bronze Brass Aluminium Stainless steel Steel (N/mm2) < 1200 Steel (N/mm2) < 1000 Steel (N/mm2) < 800 06 159
DIN 5156 B HSSE Co 5 DIN 5156 C HSSE Co 5 DIN 374 HSSE Co 5 DIN 374 Page HSSE Co 5 Article no.
Steel (N/mm2) < 1000 Steel (N/mm2) < 1200 < 800 N/mm² <1000 N/mm² <1200 N/mm² Main application Other application Titanium alloyed Cast iron Plastics Bronze Brass Aluminium Stainless steel Steel (N/mm2) < 800 06 161
06 Product information for machine taps HSS 800 N/mm² ISO 2 6H 60° HSS The machine tap consists of heavy-duty high-speed steel. For through threads and bottoming threads in unalloyed steels up to a strength of 800 N/mm², malleable.The thread is cut in one operation.
06 Product information for machine taps 900 HSS N/mm² ISO 2 6H 60° HSS-TiN The machine tap consists of heavy-duty high-speed steel with a titanium nitride coating. For universal use on a wide range of materials due to layer of hard material! For through threads and bottoming threads in unalloyed and alloyed steels up to a strength of 900 N/mm², stainless steel. The thread is cut in one operation. Note: cutting speeds from 10 m/min.
B M DIN 371 60° ISO 2 6H 4 Ø1 L2 Machine taps M DIN 371 HSS and HSSE-Co 5, ground Machine taps with reinforced shank for through threads.
M DIN 371 60° ISO 2 6H 4 Ø1 06 L2 C HSS HSSE Co 5 Machine taps M DIN 371 HSS and HSSE-Co 5, ground Machine taps with reinforced shank and 35° right-hand spiral flutes for bottoming.
B M DIN 376 ISO 2 6H 4 60° Ø1 L2 Machine taps M DIN 376 HSS and HSSE-Co 5, ground Machine taps with overflow shank for through threads. Chamfer: Thread: Flanks: type B, 4 - 5 threads with progressive tap metric, DIN ISO 13 relief-ground L1 06 HSS HSSE Co 5 Packing unit: individual plastic pack Schematic illustration. Smaller diameters can be supplied with a tip for production reasons.
C HSS HSSE Co 5 M DIN 376 60° 4 ISO 2 6H Ø1 L2 Machine taps M DIN 376 HSS and HSSE-Co 5, ground 06 Machine taps with overflow shank and 35° right-hand spiral flutes for bottoming. type C / 35° right-hand spiral flutes, 2 - 3 threads metric, DIN ISO 13 relief-ground L1 Chamfer: Thread: Flanks: Packing unit: individual plastic pack Schematic illustration. Smaller diameters can be supplied with a tip for production reasons.
HSS HSSE Co 5 DIN 371/376 4 60° ISO 2 6H Machine tap sets HSS and HSSE-Co 5, in steel case HSSE Co 5 HSS HSSE Co 5 HSSE Co 5 HSS B 7-piece set of machine taps M DIN 371 / 376 type B with progressive tap M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 245 057 245 061 245 063 245 065 245 068 C 7-piece set of machine taps M DIN 371 / 376 type C / 35° right-hand spiral flutes M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 245 058 245 062 245 064 245 066 245 069 — — — C 14-piece set of machine
HSS HSSE Co 5 DIN 371/376 4 60° ISO 2 6H 06 Machine tap sets HSS and HSSE-Co 5, in plastic case HSS HSSE Co 5 HSSE Co 5 HSSE Co 5 HSS B 7-piece set of machine taps M DIN 371 / 376 type B with progressive tap M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 245 057 RO 245 061 RO 245 063 RO 245 065 RO 245 068 RO C 7-piece set of machine taps M DIN 371 / 376 type C / 35° right-hand spiral flutes M 3 - M 4 - M 5 - M 6 - M 8 - M 10 - M 12 245 058 RO 245 062 RO 245 064 RO 245 066 RO 245069 RO —
371/376 AZ 60° 4 Ø1 L2 B HSS M ISO 2 6H Machine taps M DIN 371/376 HSS, ground with interrupted threads Chamfer: type B, 4 - 5 threads with progressive tap and interrupted threads Thread: metric, DIN ISO 13 Flanks: relief-ground L1 06 DIN Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 DIN 371 DIN 376 Machine tap with reinforced shank, for through t
C M DIN 371/376 60° 4 ISO 2 6H Ø1 06 L2 HSSE Co 5 Machine taps M DIN 371/376 HSSE-Co 5 TiCN, ground L1 Chamfer: type C / 2 - 3 threads Thread: metric, DIN ISO 13 Flanks: relief-ground Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 DIN Machine taps with reinforced shank for through-hole thread 371 in cast iron and cast alloys.
(BSP) Rp G/Rp DIN 5156 55° Ø1 4 Thread: L2 Machine taps G DIN 5156 HSSE-Co 5, ground DIN ISO 228 "G" (cylindrical pipe thread) DIN 2999 "Rp" (Whitworth pipe thread) relief-ground Flanks: L1 06 G HSSE Co 5 Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 B Machine taps with overflow shank for through threads.
B DIN 374 MF 60° 4 ISO 2 6H Ø1 L2 Machine taps MF DIN 374 HSSE-Co 5, ground Thread: metric, fine, DIN ISO 13 Flanks: relief-ground L1 06 HSSE Co 5 Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine tap with overflow shank for through threads. Nominal thread size MF Pitch mm Thread core hole Ø1 mm L1 mm L2 max.
C DIN 374 MF 60° 4 ISO 2 6H Ø1 06 L2 HSSE Co 5 Machine taps MF DIN 374 HSSE-Co 5, ground L1 Thread: metric, fine, DIN ISO 13 Flanks: relief-ground Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine taps with overflow shank and 35° right-hand spiral flutes for bottoming. Nominal thread size MF Pitch mm Thread core hole Ø1 mm L1 mm L2 max.
UNC B UNC 60° 4 2B Ø1 L2 Machine taps UNC HSSE-Co 5, ground Thread: American UNC coarse thread Flanks: relief-ground L1 06 HSSE Co 5 Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine taps with reinforced shank for through threads. Nominal thread size UNC Threads per inch Thread core hole 1 mm L1 mm L2 mm Ø2 mm Nr. 4 Nr. 5 Nr. 6 Nr. 8 Nr.
UNC C UNC 60° 4 2B Ø1 06 L2 HSSE Co 5 Machine taps UNC HSSE-Co 5, ground L1 Thread: American UNC coarse thread Flanks: relief-ground Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine taps with reinforced shank and 35° right-hand spiral flutes for bottoming.
UNF B UNC 60° 4 2B Ø1 L2 Machine taps UNF HSSE-Co 5, ground Thread: American UNF fine thread Flanks: relief-ground L1 06 HSSE Co 5 Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine taps with reinforced shank for through threads. Nominal thread size UNF Threads per inch Thread core hole Ø1 mm L1 mm L2 mm Ø2 mm Nr. 4 Nr. 5 Nr. 6 Nr. 8 Nr.
UNF C UNC 60° 4 2B Ø1 06 L2 HSSE Co 5 Machine taps UNF HSSE-Co 5, ground L1 Thread: American UNF fine thread Flanks: relief-ground Packing unit: individual plastic pack Steel (N/mm2) < 800 Brass Steel (N/mm2) < 1000 Bronze Steel (N/mm2) < 1200 Plastics Rust-resistant steel Cast iron Aluminium Titanium alloyed Ø2 Machine taps with reinforced shank and 35° right-hand spiral flutes for bottoming. Nominal thread size UNF Threads per inch Thread core hole Ø1 mm L1 mm L2 mm Ø2 mm Nr.
PG HSS B 80° Ø1 4 L2 Machine taps PG HSS, ground Machine taps with overflow shank for through threads.
D HSSE Co 5 DIN 2174 M 60° ISO 2 6H 4 Ø1 L2 Forming taps DIN 2174 HSSE-Co 5-nitrated-VAP and HSSE-Co 5-TiAlN, ground 06 Forming taps with reinforced shank for through threads and bottoming. metric, DIN ISO 13 relief-ground L1 Thread: Flanks: As shaping is done without cutting, no interruption of the course of the fibre in the material. The deformation creates very rigid threads. Consistent accuracy even with high productivity.
HSS S1 L2 Combined machine drill taps “long series” and “short series” HSS and HSS-TiN ground L1 06 M Ø1 ISO 2 6H Combined machine drill tap with ¼” hexagon shank for drilling and through hole tapping in a single operation Flanks: Shank: relief-ground 6,35 x 27,0 mm The combined machine tap is suitable for sheet metal working with right/left handed rotation cordless drilling machines. The thread is cut in one operation, without any tool changing.
HSS ISO 2 6H 06 7-piece set of combined machine taps "long" 6 combined machine taps M 3 - M 4 - M 5 - M 6 - M 8 - M 10 + 1 hexagon magnetic holder HSS HSS 270 020 270 020 T 270 020 T Combined machine drill tap sets “long series” HSS and HSS-TiN ground in steel case Combined machine drill tap sets “short series” HSS and HSS-TiN ground in steel case 7-piece set of combined machine taps "short" 6 combined machine taps M 3 - M 4 - M 5 - M 6 - M 8 - M 10 + 1 hexagon magnetic holder HSS R 270 020 R
High-performance twist drills DIN 338 HSS ground 1 06 1 2 SW ground version, made to match the drilling jigs exactly Ø mm Ø inch for stud size Length mm 3,2 4,8 6,4 8,0 8,7 1/8 3/16 1/4 5/16 11/32 1-4 5-7 8 9 10 65,0 86,0 101,0 117,0 125,0 4 214 032 214 048 214 064 214 080 214 087 Size For threads Ø mm Ø inch Length mm 1 2 3 4 5 M 5-M 6 M 7-M 8 M 9 - M 10 M 12 M 14 - M 16 3,2 4,8 6,4 8,0 8,7 1/8 3/16 1/4 5/16 11/32 60,0 70,0 78,0 83,0 94,0 4 L Ø3 Ø2 3 made of special steel prof