I NSTALLATION/ O PERATION M ANUAL 3Dimension™ Series D-73d LED Home Theater Projection System
RuncoCare™ Standard Two Year Limited Warranty Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years of unparalleled video performance. Y This RuncoCare Standard Limited Warranty is provided free of charge by Runco International, LLC (“Runco”) with the purchase of a covered Runco product.
RuncoCare Claim Procedure In the event of a product defect, please follow the warranty claim procedure provided below: 1. The Customer is required to contact a Runco dealer or Runco Technical Support via email at support@runco.com or via phone at (toll free) (800) 23-RUNCO (800-237-8626). If the customer is located outside North America, call +3589 4200 554 in Europe for product service. 2.
h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed i Customer caused defects, including but not limited to, scratched/defaced/altered plastics j Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for regular cleaning of the product k Opening the product and/or tampering with internal circuitry l Products lost, stolen or discarded m Any damage or dissatisfaction associated with laten
Exclusion of Damages RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. 1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Important Safety Instructions Thank you for your purchase of this quality Runco video product! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D VIEWING: Please read and make sure you understand the following safety information before using the product for viewing 3D content. Provide this information to the end users of this product and ensure that they understand it. EL IM IN A R Y It is widely recognized that stereographic display devices can cause discomfort, including, without limitation, dizziness, nausea, headaches, eye fatigue and eye-strain, in some individuals.
Compliance Information EUROPEAN UNION (EU) DECLARATION OF CONFORMITY: Manufacturer’s Name: Runco International, LLC Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992 conform with the provisions of: EL IM IN A R D-73d, D-73d/CineWide and D-73d/CineWide with AutoScope Y hereby declares that the Products’ Model Numbers: Council Directive 2004/108/EC on Electromagnetic Compatibility; EN 55022 “Limits and methods of measurements of radio interference characteristics of information te
FCC PART 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. • Reorient or relocate the receiving antenna. EL IM IN A R • Increase the separation between the equipment and receiver.
1 Table of Contents RuncoCare™ Standard Two Year Limited Warranty ................................................... iii Important Safety Instructions ....................................................................................... vii Compliance Information ................................................................................................ ix 1. Introduction ...............................................................................................................
Table of Contents Folded Optics .......................................................................................................28 Audio/Video Synchronization Issues......................................................................29 Ventilation .............................................................................................................30 Other Considerations ............................................................................................
Table of Contents 4. Operation .................................................................................................................65 Using the On-Screen Menus ......................................................................................65 Main Menu............................................................................................................67 Input Source .........................................................................................................
Table of Contents PR EL IM IN A R Y Notes: xiv D-73d Series Installation/Operation Manual
1 List of Figures 2-1. D-73d Series LED 3-D Home Theater Projection System Block Diagram......................7 2-2. Standard D-73d Projector Functional Components ......................................................8 2-3. D-73d Rear Panel.........................................................................................................9 2-4. Primary DHD Controller Front Panel............................................................................11 Y 2-5. Primary DHD Controller Rear Panel .
List of Figures 3-27. Shasta Anamorphic Lens Mounting Assembly - Exploded View................................57 3-28. Keystone and Pincushion Distortion .........................................................................61 3-29. Image Alignment Controls ........................................................................................62 4-1. D-73d OSD Menu Structure .......................................................................................65 4-2.
1. Introduction This Owner’s Manual describes how to install, set up and operate the Runco D-73d Series LED 3-D Home Theater Projection System. 1.1 About This Manual Y Throughout this manual, the Runco D-73d Series LED 3-D Home Theater Projection System are referred to collectively as the “D-73d.” EL IM IN A R Runco has prepared this manual to help home theater installers and end users get the most out of the D-73d.
Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: Note NOTES emphasize text with unusual importance or special significance. They also provide supplemental information. Caution CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction.
Introduction Y Runco’s exclusive new D-73d Series LED 3-D Home Theater Projection System integrates 3D visualization technology that is based on the science of how the human eye and brain process actual depth and dimension in real life, Runco has created a flawless stereoscopic video reproduction that is unlike anything else in the home or private cinema market.
Introduction With Runco CineWide, the projection system is able to use the full pixel array, thereby producing a 2.35:1 image with enhanced resolution and increased brightness. No resolution or image area is lost to those black bars that contain no picture information. CineWide with AutoScope provides a motorized, remote-controlled anamorphic lens mechanism.
Introduction Your D-73d is shipped with the following items. If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO. • D-73d Series LED 3-D Home Theater Projection System: • Projector • Two (2), DHD Controller units (Primary and Secondary) • 3Dimension Processor • Remote Control Unit and two (2), AAA-size batteries • AC Power Cords (5) • 5.
Introduction PR EL IM IN A R Y Notes: 6 D-73d Series Installation/Operation Manual
2. System Overview The D-73d Series LED 3-D Home Theater Projection System consists of the following components: • The projector, consisting of two discrete LED optical engines stacked one on top of the other to provide either two-dimensional (2D) or three-dimensional (3D) content. EL IM IN A R Y • A Primary DHD Controller unit that provides a video signal and on-screen display (OSD) menu to the “left eye” optical engine of the projector.
System Overview 2.1 Projector The standard D-73d projector, shown Figure 2-2, consists of two discrete LED optical engines stacked one on top of the other to provide either three-dimensional (3D) or two-dimensional (2D) content. For 3D content, each engine produces the image for one eye. Linear polarizers on each engine isolate the output images from one another.
System Overview • LENS LOCK The screw to the right of the lens activates the lens lock, which freezes the zoom and lens shift settings to keep the projector images aligned over time. When shipped from Runco, the lenses are unlocked. To lock the lens position, use the same 5.0-mm Hex wrench (provided) that you use for lens shift adjustments. (Turn clockwise two or three turns.) WARNING THE LENS SHIFT MECHANISM CAN BE DAMAGED BY EXCESSIVE FORCE.
System Overview 1. POWER INPUT (Left-Eye Engine – 100 to 240 VAC) Connect the left-eye optical engine to power here. 2. DHD INPUT (Left-Eye Engine) An HDCP-compliant digital video input for connecting the HDMI Out (To Display) from the Primary DHD Controller. 3. RS-232C INPUT (Left-Eye Engine) (9-pin, female D-Sub) Connect the Display Control output on the Primary DHD Controller to this input (see Figure 2-5). 4.
System Overview 2.2 Primary DHD Controller The Primary DHD Controller provides a video signal and OSD menu to the left-eye optical engine of the projector. It controls the other D-73d system components in response to user input via the following interfaces: • Front-panel keypad • IR remote control unit • HDMI CEC messages • RS-232 serial commands Y • Ethernet EL IM IN A R Figure 2-4 shows the controls and indicators on the Primary DHD Controller front panel; the paragraphs that follow describe them.
System Overview 6. DOWN BUTTON Use to direct-select aspect ratios or move the menu cursor down in the OSD. When no menu is present on-screen, this button toggles through aspect ratios in the following order: 16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema - Native 7. RIGHT BUTTON Used to direct-select inputs or move the menu cursor right in the OSD.
System Overview 3. USB A standard, USB Series “B” connection to a personal computer, for performing software upgrades and other service procedures. 4. RS-232 (To Accessory Box) A male, 9-pin D-sub connector for interfacing with the Secondary DHD Controller. (Use a “null-modem” serial cable for this connection. 5. Display Control Connect this to the RS-232 input on the left-eye (top) optical engine on the D-73d projector. EL IM IN A R Y 6.
System Overview 2.3 Secondary DHD Controller The Secondary DHD Controller provides a video signal and OSD menu to the right-eye optical engine of the projector. 1 2 EL IM IN A R Y Figure 2-6 shows the Secondary DHD Controller front and rear panel. 3 TRIGGERS Do not connect video sources or control systems to this box.
System Overview 7. HD2 Input (5 x Analog BNCs) Connect the HD 2 input to the Right Analog output on the 3Dimension Processor. The HD 1 input is not used with the D-73d. Connect your Component/RGBHV sources to the 3Dimension Processor. 8. Video 1 Input Connect the Video 1 input to the Right Composite video output on the 3Dimension Processor. The Video 2 and Video 3 inputs are not used with the D-73d. Connect your Composite video sources to the 3Dimension Processor. Y 9.
System Overview 1. RUNCO ICON Lights blue to indicate that the 3Dimension Processor is on or powering up. 2. MAIN POWER SWITCH Disconnects or applies power to the 3Dimension Processor. 3. POWER INPUT (100 to 240 VAC) Connect the 3Dimension Processor to power here. 4. HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4 In (Digital) HDCP-compliant digital video inputs for connecting an HDMI or DVI source. Y 5. Component / SCART In (3 x RCA connectors) SD/HD input for connecting SDTV, EDTV or HDTV component video sources.
System Overview Figure 2-8 shows the D-73d remote control, and the paragraphs that follow describe its functionality. 1 LIGHT 2 3 ON OFF 5 I N P U T EN T ER 7 6 RATIO EXIT 8 ISF NT 9 VID 1 10 HD 1 HDMI 1 ISF DAY 1 4 7 CUST 1 VID 2 HD 2 HDMI 2 2 MENU CUST 2 VID 3 3 11 COMP 5 6 SCART 8 13 9 PR 12 HDMI 3 14 I N P U T EL IM IN A R 4 Y RATIO HDMI 4 NATIVE 0 16 : 9 4:3 LET BOX V-WIDE CINEMA V-CINE Figure 2-8.
System Overview 1. IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted. 2. LIGHT Press to illuminate the buttons. 3. ON / OFF Press to turn the DHD Controller and projector on or off. 4. ENTER Press to select a highlighted menu item or confirm a changed setting. Y 5. Cursor Buttons ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns.
System Overview 10. HD 1 (4) / HD 2 (5) Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “4” or “5.” 11. COMP (Component) (6) Press to select the Component video input as the source or to enter the numeric character “6.” 12. HDMI 1 (7) / HDMI 2 (8) / HDMI 3 / HDMI 4 (0) Press to select an HDMI input as the source or to enter the numeric character “7,” “8” or “0.” EL IM IN A R 14.
System Overview PR EL IM IN A R Y Notes: 20 D-73d Series Installation/Operation Manual
3. Installation Installation must be performed by a qualified custom video installation specialist. Y Note To install batteries in the remote control: EL IM IN A R 1. Press down the tab on the cover and pull the cover in the direction of the arrow. 3.1 Remote Control 2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment. PR 3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place.
Installation 3.2 Quick Setup Table 3-1 gives a quick overview of the D-73d installation process. The sections following this one provide detailed instructions. Table 3-1. Installation Overview Step For Details, Refer to page...
Installation Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. 3.3 Installation Considerations Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods.
Installation Choosing A Screen ➤ Runco 3Dimension Series projectors produce exceptional 3D and 2D content. Because it is estimated that 2D content still comprises more than 90 percent of the material viewed in home theaters and private cinemas, the projection screen is a significant factor and must accommodate both 2D and 3D viewing.
Installation Estimating Throw Distance Throw Distance (TD) = Screen Width (w) x Lens Throw Ratio Scr een wid th ( w) EL IM IN A R Y TD Figure 3-1. Estimating Throw Distance Table 3-3 lists the available lens options for the D-73d and their associated throw ratios. Table 3-3. D-73d Lens Options and Throw Ratios (Note) Standard D-73d D-73d/ CineWide (Whitney Lens PR Projector Model Throw Range in Throw Range in Throw Ratio inches, with inches, with Throw Ratio with Primary 96x40.8-inch (2.
Installation Vertical and Horizontal ➤ Position Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center is aligned with either the top or bottom edge of the screen area, and centered horizontally. See Figure 3-2.
Installation 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Center Y 0% EL IM IN A R Screen Width (W) PR Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example. Figure 3-4.
Installation Table 3-4 lists the usable lens shift ranges for each available D-73d lens, as percentages and absolute measurements with a 96 x 54 inch (1.78:1) screen. Table 3-4.
Installation Tip For best performance, always use “first-surface” mirrors in your rear-projection installation (as opposed to conventional, “second-surface” mirrors with the reflective surface behind a transparent substrate such as glass or acrylic). First-surface mirrors provide a strict reflection without the “ghosting” effect seen with a second surface mirror, where a faint secondary reflection could be observed coming from the front surface of the glass.
Installation Ventilation ➤ If you are mounting the D-73d in an enclosure, leave at least 3 inches (76.2 mm) of space on the left and right sides between it and surrounding objects, as shown in Figure 3-6. This allows heat to disperse, maintaining the proper operating temperature. EL IM IN A R Y Minimum 3.0 in. (76.2 mm) Clearance for airflow Figure 3-6.
Installation If you are installing a standard D-73d (without an anamorphic lens), skip this step and proceed with Mounting the D-73d (page 36). If you are installing a D-73d/CineWide, proceed with Installing the Fixed CineWide Base Plate (D-73d/CineWide) (page 34). 3.4 Installing the Optional Anamorphic Lens Mount If you are installing a D-73d/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor. 1.
Installation Installing the Lens Motor: 1. Position the AutoScope lens motor as shown in Figure 3-7. 2. Line up the mounting holes on the lens motor housing with those on the underside of the projector. 3. Secure the motor to the projector with the eight (8) supplied M6 x 12mm Pan-Head Phillips screws. EL IM IN A R Y Screw, Phillips 2 Pan-Head, M6-1.0 x 12mm (8x) PR 1 AutoScope Lens Motor Figure 3-7.
Installation Connecting the AutoScope Lens Motor to the Projector: Connect the AutoScope lens transport motor to the 12-volt trigger output on the projector (labeled CINEWIDE/AUTOSCOPE), as shown in Figure 3-8. Y PRIMARY EL IM IN A R PRIMARY 3.5-mm mini plug SECONDARY PR SECONDARY +12V Trigger Input Power Switch AC Input Anamorphic Lens Transport Motor Figure 3-8.
Installation D-73d/CineWide with Whitney Anamorphic Lens: Figure 3-9 shows the Whitney anamorphic lens base plate assembly for a D-73d/CineWide. PR EL IM IN A R 2 Screw, Phillips Pan-Head, M5-0.8 x 10mm (2x) Y Installing the Fixed ➤ CineWide Base Plate (D-73d/CineWide) 1 CineWide Base Plate for Whitney Lens Figure 3-9. D-73d/CineWide with Whitney Anamorphic Lens Base Plate Exploded View To install the Whitney anamorphic lens base plate on a D-73d/CineWide: 1.
Installation D-73d/CineWide with Shasta Anamorphic Lens: Figure 3-10 shows the Shasta anamorphic lens base plate assembly for a D-73d/CineWide. EL IM IN A R Y 2 Screw, Phillips Pan-Head, M5-0.8 x 20mm (4x) PR Rectangular 3 Spacer (2x) 1 CineWide Base Plate for Shasta Lens Figure 3-10. D-73d/CineWide with Shasta Anamorphic Lens Base Plate Exploded View To install the Shasta anamorphic lens base plate on a D-73d/CineWide: 1. Place the projector upside down on a blanket or other soft, flat surface. 2.
Installation 3.5 Mounting the D-73d There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. Floor Mounting (Upright) ➤ For fixed installations, and for those that want the projector out of sight or have a limited space for projector and audience, you can invert the D-73d and suspend it from the ceiling using a specially-designed ceiling mount fixture.
Installation The DHD Controller units and 3Dimension Processor can be placed on any flat, stable surface such as a shelf or table, or they can be rack-mounted using the supplied mounting hardware. Place these components in a location that provides easy access to the power connectors. Primary DHD Controller 3Dimension Processor Y The DHD Controller units and 3Dimension Processor each require 2U (3.5 inches) or more of vertical rack space (at least 10.5 inches total).
Installation 3.7 System Interconnections Proceed as follows to connect the D-73d system components to each other and to AC power. When connecting your equipment: • Turn off all equipment before making any connections. • Use the correct signal cables for each source. • For best performance and to minimize cable clutter, use high-quality cables that are only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.
Installation Figure 3-14 shows how to connect the Primary and Secondary DHD Controllers to the projector. Primary DHD Controller PRIMARY TRIGGERS Do not connect any video source directly to this box.
Installation Connecting the Primary ➤ and Secondary DHD Controllers to Each Other and to the 3Dimension Processor Figure 3-15 shows the connections between the 3Dimension Processor and Primary and Secondary DHD Controllers. Primary DHD Controller TRIGGERS Do not connect any video source directly to this box.
Installation To make these connections easier, the rear-panel connectors on the 3Dimension Processor and DHD Controllers are identified and color-coded as follows: Identifier A, B, C, D, E Color/Function Green - Analog (HD) video from 3Dimension Processor to Primary DHD Controller Red - Analog (HD) video from 3Dimension Processor to Secondary DHD Controller F Green - Analog (SD) video from 3Dimension Processor to Primary DHD Controller G EL IM IN A R Y Red - Analog (SD) video from 3Dimension Process
Installation The Primary DHD Controller provides a second HDMI output (labeled HDMI Out (Audio Only)) for connection to an audio receiver/switching system or secondary display device for monitoring purposes. See Figure 3-16. The DHD Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. For more information about CEC, refer to Using HDMI CEC Messages on page 112.
Installation The Primary DHD Controller provides the following interfaces to external equipment that allow it to control or be controlled by that equipment: • An RS-232 interface to a PC or control/automation system; • Three (3), 12-volt trigger outputs; • An infrared (IR) repeater input; • An Ethernet network interface for firmware updates and maintenance notifications. The following sections describe how to make these interface connections.
Installation Connecting 12-volt Trigger Outputs to External Equipment: Connect any 12-volt trigger-activated equipment (such as retractable screens or screen masks) to the 12-volt trigger outputs on the Primary DHD Controller; see Figure 3-18. Retractable Screen or other 12-volt trigger-activated device Sleeve = Ground Tip = +12V TRIGGERS EL IM IN A R Y box. 1 2 Component/SCART Component/ F USB 3 Y Video 1 Video 2 Pb Pr Video 3 H HDMI 1 G HDMI 3 HDMI 2 HDMI 4 HD1 HD2 Figure 3-18.
Installation Ethernet Network Connection: Use a standard, Category 5 network cable with an RJ-45 plug to connect a network hub, router or gateway to the Ethernet port on the Primary DHD Controller; see Figure 3-20. For more information about configuring and using this connection, refer to Network on page 88.
Installation Connecting Source ➤ Components to the 3Dimension Processor Connect your video sources to the 3Dimension Processor as shown and described in the sections that follow. HDMI Source Connections: See Figure 3-21. Use the HDMI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector. Tip You can also connect computers with DVI output to these inputs.
Installation Component Video Source Connections: Connect your component video sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-22. IR A B C D E F G Component/SCART Y Video 1 Y G Pb B Pr R H V Video 2 IN HD1 Pb Pr Video 3 A B C D E F G Y G Pb B Pr R H V EL IM IN A R Y RCA-to-BNC adapter PR COMPONENT VIDEO OUT Y PB DTV-Set-Top Box (DTV-STB) BD/DVD Figure 3-22.
Installation RGBHV Source Connections: Connect personal computers and/or other RGB sources to the HD1 and/or HD2 inputs as shown in Figure 3-23. USB IR D E F G Y G Pb B Pr R H V INP HD1 HD2 Pr R H V Red Blue EL IM IN A R Pb B Y Y G G V-Sync F H-Sync E Green D RGB Camcorder Computer PR or Figure 3-23.
Installation SCART RGBS Source Connections: Connect the green, blue and red outputs from your SCART source to the Component/SCART input on the 3Dimension Processor. Connect the sync output from your SCART source to the Video 1 input on the 3Dimension Processor. See Figure 3-24.
Installation Composite Source Connections: See Figure 3-25. INPUTS A Component/SCART 3Dimension HDMI 1 HDMI 3 HDMI 2 H I4 Y Video 1 Video 2 Pb Pr Video 3 A Camcorder Composite EL IM IN A R VCR Composite Composite Y Processor Composite Composite Gaming Console Composite Figure 3-25. Composite Video Source Connections Connecting to AC Power ➤ Plug the female end of a power cord into each AC receptacle on the rear of the D-73d (AC 100V ~ 240V); see Figure 2-3.
Installation At this point you are ready to perform the initial power-up sequence and optical alignment procedure, which is summarized in Table 3-6 and described in detail in the sections that follow. This procedure assumes the following: 3.8 Power-Up Sequence and Optical Alignment Procedure • You are installing a projector equipped with anamorphic lenses. (If not, you can skip those tasks relating to the anamorphic lenses.
Installation Table 3-6. D-73d Optical Alignment Procedure (with Anamorphic Lenses) (continued) DHD 1. Note: The default warp is 23 pixels on the left and right sides (x) and 13 pixels at the top and bottom (y). If more is needed, use the “Image Alignment” controls to increase it. EL IM IN A R Y 2. Select Calibration -> Adjustment Mode and set it to Secondary. Select Service -> Test Video and choose Secondary Alignment. Projector (Align Secondary/Right Image with Screen) 1.
Installation Table 3-6. D-73d Optical Alignment Procedure (with Anamorphic Lenses) (continued) DHD 1. Select Aspect Ratio and set it to Cinema. 2. Select Calibration -> Image Alignment -> Corner Alignment and adjust corners. 3. Select Calibration -> Image Alignment -> Midpoint Alignment and adjust midpoints. Projector No adjustment needed. Note: The DHD Controller saves the Image Alignment (warp) settings for each aspect ratio.
Installation 4. Press the ON button on the remote control (or the ON/STANDBY ( ) button on the Primary DHD Controller front panel) to turn on the system. The vacuum fluorescent display on the Primary DHD Controller front panel briefly displays “Initializing System,” followed by “Starting D-73d.” 5.
Installation 8. Focus Left (Top) Primary Lens: To focus the projected image, grasp the lens by the outer ring and rotate it. Focus 9. Adjust Zoom on Left (Top) Primary Lens: To make the projected image smaller (zoom out) or larger (zoom in), move the zoom tab in the appropriate direction. Zoom Y Projection Lens EL IM IN A R 10.
Installation Adjusting the Picture ➤ Orientation By default, the D-73d is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this: 1. On the DHD Controller remote control or front panel, press MENU. 2. Select Service from the Main Menu. 3. Select Display Device from the Service Menu. 4.
Installation 1. Remove the two Yaw/X Adjustment Levers and Washers (5) from the bottom of the Anamorphic Lens Holder (2). 2. Place the Anamorphic Lens Holder on top of (or under, if the projector is inverted) the CineWide Base Plate. Position the bracket so that the slots at the bottom of the lens holder are perpendicular to the corresponding slots on the base plate. 3. Secure the Anamorphic Lens Holder to the plate using the Hex Bolts/Washers (4) and Yaw/X Adjustment Levers that you removed in Step 1. 4.
Installation 1. Remove the two Yaw/X Adjustment Levers and Washers (7) from the bottom of the Anamorphic Lens Holder (2). 2. Place the Anamorphic Lens Holder on top of (or under, if the projector is inverted) the AutoScope Lens Motor Carriage Plate or CineWide Base Plate. Position the bracket so that the slots at the bottom of the lens holder are perpendicular to the corresponding slots on the base plate. 3.
Installation • Vertical Position (Y-adjust): Loosen the Height/Pitch Adjustment Knobs (Whitney anamorphic lens; see Figure 3-26) or Button-head Height Adjustment Screws (Shasta anamorphic lens; see Figure 3-27) on either side of the lens.
Installation • Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from side to side. Then, angle the lens to even out any left-right pincushion distortion: EL IM IN A R Y Anamorphic Lens (Top View) Correct Position Wrong Position PR Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to secure the lens in place. Adjusting the Right (Bottom) Anamorphic Lens: 1. On the DHD Controller remote control or front panel, press MENU. 2.
Installation Projector and/or screen placement — among other things — can cause geometric distortion in the projected image. To correct this, the DHD Controller provides precise, nine-point control over the projected image geometry. Use these controls as (and only if) needed to re-position the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) or “pincushion” distortion (mid-points not aligned with corners). See Figure 3-28.
Installation “Keystoning” usually occurs when the projector is tilted relative to the screen. “Pincushion” distortion can sometimes occur if the throw distance is very short and/or the projector is equipped with an anamorphic lens. Corner/Midpoint Alignment — 16:9 Aspect Ratio: 1. Select the 16:9 aspect ratio using either the DHD Controller remote control unit (see Figure 2-8) or the OSD menu (press MENU, then select Aspect Ratio -> 16:9). This should move the anamorphic lenses out of the optical path. 2.
Installation Note The “Left Middle y” setting also controls the “Right Middle” y-coordinate. Similarly, the “Top Middle x” setting also controls the “Bottom Middle” x-coordinate. Corner/Midpoint Alignment — Cinema (2.35:1) Aspect Ratio: 1. Select the Cinema aspect ratio using either the DHD Controller remote control unit (see Figure 2-8) or the OSD menu (press MENU, then select Aspect Ratio -> Cinema). This should move the anamorphic lenses back into the optical path, in front of the primary lenses.
Installation PR EL IM IN A R Y Notes: 64 D-73d Series Installation/Operation Manual
4. Operation To display the Main Menu, press the MENU button on the remote control or Primary DHD Controller front panel. To select a menu item, use the and buttons on the remote control or Primary DHD Controller front panel to highlight it. Then, to confirm your selection, press ENTER on the remote control or DHD Controller front panel. 4.
Operation Color Bars 1 Color Bars 2 Focus Grey Bars Primary / Secondary / Dual Alignment Rename/Restore Input Names Display Device - Configure Picture Orientation Auto, Floor Front, Ceiling Front, Floor Rear or Ceiling Rear Lamp Info.
Operation The Main Menu is the starting point for accessing all DHD Controller functions. Main Menu (You must enter a passcode to access the Calibration and Service menus.) Runco Video Input Source Aspect Ratio When you set the Adjustment Mode to Primary or Secondary, the Main Menu title becomes “Runco Video (Pri.)” or “Runco Video (Sec.)” respectively. Memory Presets EL IM IN A R Y Note You must perform and save all image adjustments on both the Primary and Secondary DHD Controllers.
Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key 16:9 16:9 Description Select 16:9 to view 16:9 DVDs and HDTV programs in their native aspect ratio. EL IM IN A R Y 16:9 Image on 16:9 Screen (Display) 4:3 images are stretched horizontally to fit a 16:9 screen. 4:3 Image, stretched to fill 16:9 Screen (Display) 4:3 VirtualWide 4:3 Image on 16:9 Screen (Display) Standard 4:3 scales the input signal to fit in the center of the 16:9 screen.
Operation Table 4-1. Aspect Ratio Settings (continued) Remote Control Key Cinema CINEMA Description Select Cinema to view 2.35 source material in its native aspect ratio. EL IM IN A R 2.35:1 Image on 16:9 Screen (Cinema aspect ratio / no CineWide) 2.35:1 Image on 2.35:1 Screen (Cinema aspect ratio / CineWide) Virtual Cinema V-CINE PR 16:9 16:9 Image Image on on 2.35:1 2.
Operation Screen ➤ The Screen Menu allows you to recall multiple sets of stored values for certain controls (Output Shift and Image Alignment, to name two) that are saved for each aspect ratio. Such settings are also saved “per screen.” To recall the Output Shift and Image Alignment settings associated with “Screen 1” or “Screen 2,” make that selection here. Picture ➤ Use the controls in the Picture Menu to calibrate each DHD Controller input to achieve optimum picture quality.
Operation Y Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2 shows a typical PLUGE pattern. Above Black EL IM IN A R Below Black Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.
Operation blue red EL IM IN A R Y magenta green cyan yellow gray Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4. Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint 1. Press the MENU button on the remote control or DHD Controller front panel. 2. Select Service from the Main Menu and press ENTER. 3. Enter the Service menu passcode. 4. Select Display Device from the Service menu and press ENTER. 5.
Operation EL IM IN A R Y blue red magenta green cyan yellow gray 11.Adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener.
Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. PR Figure 4-5.
Operation Height: Select Height from the Input Position menu to change the projected image height. Press to increase the height; press to decrease it. Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area.
Operation Phase (RGB, Component or SCART sources): This control adjusts the phase of the pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB, Component or SCART image still shows shimmer or “noise” after Tracking has been optimized. Adjust the Phase after adjusting Tracking (see below). Tip Y For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image.
Operation You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected: • Brightness • Contrast • Color saturation • Tint • Sharpness • Gamma • Color temperature and white balance or to highlight it and press ENTER.
Operation • Choose Frame Packing to have the 3Dimension Processor decode frame packed data into left and right eye data. In this mode, the DHD Controllers do not perform any 3D processing. Reverse Eyes: By default, the Primary and Secondary DHD Controllers are dedicated to “left eye” and “right eye” image processing respectively. To reverse this relationship, choose Reverse Eyes from the 3D Processing menu and set it to On.
Operation Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only. Calibration Calibration Note You must enter a passcode to access the Calibration menu. ISF Settings Display Color Input Image To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the Memory Presets menu (see page 76) or use the corresponding remote control buttons.
Operation • Color Temp: Select Color Temp from the Display Color - Common Settings menu to adjust the color temperature. Color temperature establishes the “color of gray” by adjusting the 75% white point to various color points. What are “color points?” A “color point” is an x/y coordinate pair that defines a color’s location on the standard CIE chromaticity graph, shown in Figure 4-7.
Operation • Color Gamut: Select Color Gamut from the Display Color - Common Settings menu to select a color gamut (range) that may be different from the default color gamut. Each setting defines the precise hue of each primary (red, green and blue) and secondary (yellow, cyan and magenta) color component used to generate the millions of colors produced in displays. Changing this setting relocates the “triangle” for possible colors (see Figure 4-7).
Operation The DHD Controller uses the PCE settings for all display modes on a given input. Note • Hue/Saturation/Level: PCE provides the ability to define a custom color gamut in terms of primary (red, green and blue) and secondary (yellow, cyan and magenta) color hues, saturation and level (brightness). EL IM IN A R Y Each control operates only on the color specified. Surrounding colors are linearly interpolated based on their distance from each of these colors.
Operation Display Color - Projector Settings: These settings are also saved independently for each input and display mode. • SatCo (BrilliantColor™): Select SatCo (BrilliantColor™) from the Display Color Projector Settings menu to enable (On) or disable (Off) BrilliantColor processing, which improves brightness in grays and secondary colors. • ConstantContrast: Select ConstantContrast from the Display Color - Projector Settings menu to enable (On) or disable (Off) ConstantContrast in the optical engine.
Operation Memory Preset Copy/Paste - Memory Preset: You can copy and paste settings from one memory preset to another. This gives you a convenient starting point for creating a new preset based on an existing one, to make the calibration process less time-consuming. Aspect Ratio For example, you can use the Copy/Paste Memory Preset feature to: Copy/Paste • Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
Operation • Aspect Ratio - Paste Settings: To apply the Output Shift and Image Alignment settings on the clipboard to a different aspect ratio and/or screen, do either of the following: • Switch to another aspect ratio (for example, from 16:9 to Cinema). • Switch from Screen 1 to Screen 2 or vice versa. Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings are saved automatically.
Operation Service ➤ Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only. Service Test Video Note Input Names You must enter a passcode to access the Service menu. Display Device Network Test Video: Select Test Video from the Service Menu to access the internal test patterns on the DHD Controller. Table 4-4 lists the available test patterns and describes their suggested usage.
Operation Table 4-4. Test Patterns and Their Suggested Usage Pattern Suggested Usage Use this pattern when aligning the output from the projector’s primary or secondary optical engines (refer to Power-Up Sequence and Optical Alignment Procedure on page 51). Select Dual Alignment to have both optical engines output this pattern. Y Primary Alignment Secondary Alignment Dual Alignment Press MENU to exit test pattern mode. EL IM IN A R Input Names: You can give each input a descriptive name.
Operation Network: The options in the Network menu allow you to configure the network communication features. • IP Configuration: Select IP Configuration from the Network menu to either set the IP address, subnet mask and default gateway of the DHD Controller manually or obtain these settings automatically, from a DHCP (Dynamic Host Configuration Protocol) server. (Most broadband routers and gateways support DHCP.) You can also test the network connection from this menu.
Operation If you prefer to do this manually, set it to Off. The DHD Controller will ask if you want to perform the upgrade the next time it is power-cycled. • Check For New Firmware: To have the DHD Controller check for new firmware on demand (and perform an upgrade if it finds a new version), select Check For New Firmware from the Auto Firmware Upgrade menu. If the DHD Controller finds a new firmware version, select Yes to perform the upgrade or No to return to the previous menu.
Operation • Error Notification: To have the DHD Controller send a message to the destination e-mail address when a “DHD Error” or “Display Error” occurs, select Error Notification from the E-Mail Notification menu and set it to On. • Error Notification to Runco: To have the DHD Controller send an e-mail message to Runco Customer Support when a “DHD Error” or “Display Error” occurs, select Error Notification to Runco from the E-Mail Notification menu and set it to On.
Operation • Remote Network Control: Select Remote Network Control from the Network menu to enable or disable control of the DHD Controller via an IP connection (typically using a web browser). Set it to On to allow all incoming remote network connectivity. Set it to Off to disable any incoming network communication that was not initiated by the DHD Controller. Note This setting has no effect on the E-Mail Notification or Auto Firmware Upgrade functions.
Operation • OSD Messages: When you select a new aspect ratio, input source or memory preset, the DHD Controller briefly displays an on-screen message confirming your new selection. To prevent the display of these messages, select OSD Messages from the Miscellaneous menu to and set it to Off. • Blank Screen Color: Select Blank Screen Color from the Miscellaneous menu to select the color that appears when no incoming signal is present.
Operation Sync Threshold: Select Sync Threshold to adjust the threshold at which negative pulses on the component video green/luma channel are interpreted to be sync pulses. Sync Threshold adjustment is occasionally necessary when a DVD player or HDTV source signal drops “below black” (for example, during scenes with explosions or when subtitles are present) and causes the projector to temporarily lose sync.
Operation Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust the brightness of the front-panel LED and LCD status indicators. Standby LED LCD Y Logo LED EL IM IN A R • Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the large, illuminated logo on the left side of the display. The range is from 0 (off) to 31. Note During a firmware upgrade, this LED lights at full brightness regardless of the Logo LED setting.
Operation Standby Mode: Select Standby Mode from the Service menu to control the DHD Controller’s power management feature. • Choose Low Power (the default setting) to have the DHD Controller shut down completely when it is turned off. This conserves power but increases the amount of time required by the DHD Controller to start up when it is turned on. • Fast Startup is a “quick-start” mode that keeps the DHD Controller running when it is turned off, even though it appears to be in standby mode.
Operation PR EL IM IN A R Y Notes: 96 D-73d Series Installation/Operation Manual
5. Maintenance and Troubleshooting The D-73d Series LED 3-D Home Theater Projection System does not require any routine maintenance to speak of, with the exception of switching, cleaning or replacing the polarizing filters in front of each primary lens. There are no other user-serviceable or -replaceable parts. Unless you are a qualified, factory-trained Runco technician, do not attempt to repair or replace any system component yourself. You will void the product warranty if you do so.
Maintenance and Troubleshooting Identifying the Left and Right Polarizers: Although the left and right polarizers have very different optical characteristics, they appear to be identical. As a result, once you remove them from the projector it may be difficult to tell them apart. Use the following technique to verify which one is which: 1. Place the polarizer on a clean, smooth, flat surface with the side that faces the projector facing up. 2.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Solution The “right-eye” optical engine does not turn on or respond to user commands. The vacuum fluorescent display on the Primary DHD Controller front panel displays the following message: • The serial connection from the Secondary DHD Controller to the “right-eye” optical engine on the display is incorrect or the cable is faulty.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Colors in the image are swapped; for example, reds appear blue or vice versa. • The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the 3Dimension Processor. • Ensure that the source outputs are connected to the correct 3Dimension Processor input. RGB-HD or Component HD images appear “noisy” or drop out intermittently.
Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Possible Cause(s) Solution AutoScope lens motor doesn’t work. • The motor is not plugged in or the AC outlet is not active. • The motor is not connected to the trigger output on the projector. • Ensure that the motor is plugged in and that the AC outlet is active. • Check the trigger connection between the lens motor and projector (Figure 3-8).
Maintenance and Troubleshooting PR EL IM IN A R Y Notes: 102 D-73d Series Installation/Operation Manual
6. External Control In addition to using the DHD Controller front-panel keypad or remote control unit, there are three methods of controlling the D-73d and DHD Controller externally: • Using a serial (RS-232) link to send ASCII commands and receive responses to those commands. • Using discrete infrared (IR) codes to program a third-party remote control unit. Y • Using an HDMI connection to send Consumer Electronics Control (CEC) commands from a BD player or other source component that supports CEC.
External Control Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters. When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >). Table 6-1.
External Control Table 6-1.
External Control Table 6-1.
External Control Table 6-1.
External Control Table 6-1. Serial Commands (continued) Command Parameter (min/max) Value Stored? Description The following serial commands are meant to emulate buttons on the remote control or DHD Controller front panel. Each button has its own serial command, so effectively it is as if you were using the IR remote only you’ll be doing so via serial commands. These commands provide active OSD responses just like the IR remote.
External Control For example, here is the RC5 control code for the ON button on the DHD Controller remote control unit (assuming the default address is used): With Toggle Bit = 0 Hex Binary 3 1 4 1 0 4 1 0 0 0 1 1 0 0 0 0 0 1 0 1 With Toggle Bit = 1 1 C 1 1 Start Bits Function 4 1 0 Toggle Bit 0 0 1 1 0 0 0 0 Y Binary 3 Address Command EL IM IN A R Hex Figure 6-1 shows the pulse train for this command (with the toggle bit set to zero).
External Control IR Command List ➤ Table 6-2 lists the RC5 control codes for the DHD Controller. Table 6-2.
External Control Table 6-2.
External Control 6.3 Using HDMI CEC Messages The DHD Controller accepts and can respond to CEC command messages from a disc player, satellite receiver or DVR/set-top box via an HDMI connection. Using CEC, the DHD Controller can perform the following actions: • Turn itself and the display device on and select the correct input when the source component initiates playback of a disc or recorded program. • Turn the source component on when you switch to its corresponding input on the DHD Controller.
External Control Table 6-3.
External Control PR EL IM IN A R Y Notes: 114 D-73d Series Installation/Operation Manual
7. Specifications 7.1 D-73d Projector Specifications Table 7-3 lists the D-73d projector specifications. Table 7-1. D-73d Projector Specifications Texas Instruments Digital Light Processing™ (DLP) dual imaging system, SuperOnyx™ DMD™ Native Resolution: Full HD 1920 x 1080 (1080p) Aspect Ratios: 4:3, Letterbox, 16:9, VirtualWide, Cinema, Virtual Cinema, Native All HDMI 1.
Specifications Table 7-1. D-73d Projector Specifications (continued) Light Output: 2D Content: CSMS Specifications* – Home Theater Calibration: 450 ANSI Lumens; 29 Foot-Lamberts (fL) Uncalibrated: 700 ANSI Lumens 3D Content: CSMS-3D Specifications** – Home Theater Calibration: 311 ANSI Lumens; 20 Foot-Lamberts (fL) Uncalibrated: 483 ANSI Lumens Y Light output will drop less than 10% over the life of the product. PR EL IM IN A R *Measured on a 1.3 gain, 72" wide 16:9 screen **Measured on a 3.
Specifications 7.2 DHD Controller Specifications Table 7-3 lists the DHD Controller specifications. Table 7-2. DHD Controller Specifications Aspect Ratios: 4:3, Letterbox, 16:9, VirtualWide, Cinema, Virtual Cinema, Native Video Standards: • • • • • • • • EL IM IN A R Y HDMI and DVI with HDCP for digital video Component and RGB HDTV (1080p, 1080i, 720p) Component and RGB EDTV (576p, 480p) Component and Composite SDTV (576i, 480i) RGB SCART with adaptor NTSC (M, 4.
Specifications Table 7-2. DHD Controller Specifications (continued) Regulatory Approvals: cTUVus, FCC class B, CE, RoHS, China RoHS, WEEE, C-Tick, CCC, local conformances as required Limited Warranty: Two (2) years parts and labor from the date of shipment from Runco. Specifications are subject to change without notice. Y Table 7-3 lists the 3Dimension Processor specifications. Table 7-3. 3Dimension Processor Specifications PR EL IM IN A R 7.
11.00 279.4 NOMINAL Y 15.95 405.0 5.50 139.7 4X 1.65 42.0 4.65 118.1 NOMINAL .46 11.7 .31 7.9 7.71 195.9 .25 6.4 2X 5.52 140.3 5.96 151.3 2X (6) CEILING-MOUNT HOLES M6 THREAD, 0.25 [6.3] DEEP LENS PLANE 20.80 528.3 MINIMUM 3.00 76.2 CLEARANCE FOR AIRFLOW 19.43 493.6 1.38 35.0 21.00 533.4 10.00 254.0 SLOT FOR CABLE ROUTING 22.94 582.7 22.80 579.1 HORIZONTAL AND VERTICAL LENS SHIFT ADJUSTERS (4 TOTAL) 4X 4.71 119.6 4.30 109.2 2.02 51.4 9.79 248.8 12.48 317.0 Figure 7-1.
Specifications 7.5 Supported Timings Table 7-4 lists the signal types supported by each input on the 3Dimension Processor. Table 7-4. Supported Signal Timings by Input 640x480 800x600 640x480 800x600 832x624 848x480 848x480 1024x768 25.175 √ Composite 1 Composite 2 Composite 3 31.469 SCART 60.00 Component Pixel Frequency (MHz) √ √ – – HDMI 1 HDMI 2 HDMI 3 HDMI 4 Horizontal Frequency (kHz) 66.59 35.892 29.862 √ √ √ – – 72.00 37.861 31.500 √ √ √ – – 75.00 37.500 31.
Specifications Table 7-4. Supported Signal Timings by Input (continued) 1400x1050 1400x1050 Pixel Frequency (MHz) Component SCART Composite 1 Composite 2 Composite 3 1360x768 Horizontal Frequency (kHz) HDMI 1 HDMI 2 HDMI 3 HDMI 4 1360x768 1280x1024 Refresh Rate (Hz) 60.00 63.981 108.000 √ √ √ – – 75.00 79.976 135.000 √ √ √ – – 85.00 91.146 157.500 √ √ √ – – 60.00 47.712 85.500 √ √ √ – – √ √ – – Y 1280x1024 Resolution 60.00 64.744 101.000 √ 60.00 65.
Specifications Table 7-4. Supported Signal Timings by Input (continued) – 50.00 SECAM – 50.00 Composite 1 Composite 2 Composite 3 PAL-N SCART – Component PAL-M HDMI 1 HDMI 2 HDMI 3 HDMI 4 Resolution 3.580 – – – – √ 15.625 3.580 – – – – √ 15.625 13.500 – – – √ √ Horizontal Frequency (kHz) 59.94/60.00 15.734/15.
Specifications Table 7-4. Supported Signal Timings by Input (continued) 1920x1080 Horizontal Frequency (kHz) Pixel Frequency (MHz) HDMI 1 HDMI 2 HDMI 3 HDMI 4 Component SCART Composite 1 Composite 2 Composite 3 23.98 26.978 74.175 – √ – – – 24.00 27.000 74.250 – √ – – – 29.97 33.716 74.175 – √ – – – 30.00 33.750 74.250 – √ – – – 50.00 56.250 148.500 – √ – – – 59.94 67.433 148.350 – √ – – – 60.00 67.500 148.500 – √ – – – 23.98 26.978 74.
Specifications PR EL IM IN A R Y Notes: 124 D-73d Series Installation/Operation Manual
020-1082-00 Rev. A May 2011 Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.
