International Home Theater System User Manual

D-73d Series Installation/Operation Manual 65
PRE
L
IMINAR
Y
4.1
Using the On-Screen
Menus
To display the Main Menu, press the MENU button on the remote control or Primary DHD
Controller front panel.
To select a menu item, use the and buttons on the remote control or Primary DHD
Controller front panel to highlight it. Then, to confirm your selection, press ENTER on the
remote control or DHD Controller front panel.
The D-73d OSD menus are arranged hierarchically, as shown in Figure 4-1. Some menu
options apply only to certain input signal types. For example, Phase and Tracking can only
be adjusted for RGB, Component video or SCART signals.
Figure 4-1. D-73d OSD Menu Structure
4. Operation
Input Source
Composite 1
Composite 2
Composite 3
Component
HD 1
HD 2
SCART
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Aspect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Screen
Screen 1 / Screen 2
Picture
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
Input Position
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
(Zoom/Crop)
Phase
(RGB/Component/SCART signals
only)
Tracking
(RGB/Component/SCART signals
only)
Memory
Presets
Recall ISF Night or ISF Day
Recall/Save Custom 1 or Custom 2
Reset Custom 1 and Custom 2 to
Factory Default
3D
Processing
3D Mode
(Auto, Off, Side-by-Side,
Top-and-Bottom or Frame Packing)
Reverse Eyes
(On/Off)
Sleep Timer
Off, 30 Minutes, 60 Minutes, 90
Minutes, 2 Hours or 4 Hours
Information
Signal
(read-only)System
Network
Field Service
Manufacturing
Calibration
Display Color -
Common Settings
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Gamma
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35 or 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Color Temp Simple (5500K, 6500K, 7500K or 9300K)
Color Gamut Auto, REC709, SMPTE-C, EBU, Native or PCE
PCE
Hue (Red / Yellow / Green / Cyan / Blue / Magenta)
Saturation (Red / Yellow / Green / Cyan / Blue /
Magenta)
Level (Red / Yellow / Green / Cyan / Blue / Magenta)
White Balance (Red / Green / Blue Gain)
Display Color -
Projector Settings
SatCo On or Off
ConstantContrast On / Off
Engine Configuration Dual / Single
Input Image
Brightness
-50, -49 ... 0 ... 49, 50
Contrast
Color
Tint
Sharpness
Input Color
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
Offset
Chroma Delay
0, 1, 2 ... 7
(Composite inputs only)
Noise Filter 0, 1, 2 ... 63
Save ISF Night
Back / Confirm
Save ISF Day
Copy/Paste
Memory Preset
Copy Settings
Paste Settings
Aspect Ratio
Copy Settings
Paste Settings
Output Shift
Left/Right
-50, -49 ... 0 ... 49, 50
Up/Down
Width
-50, -49, 48 ... 0
Height
Image Alignment
Corner Alignment
Top Left / Top Right / Bottom Left / Bottom Right /
Test Pattern Enable
Midpoint Alignment
Center / Top Middle / Left Middle / Right Middle /
Bottom Middle / Test Pattern Enable
Adjustment Mode Both, Primary or Secondary
Splash Configure
Owner Name
ISF Calibrated
ISF Other
Splash Timer 5, 6, 7 ...
15 ... 59, 60
Splash Enable On/Off
OSD Position Hor. / Ver. 0, 1, 2 ... 100
Note: Default settings appear in bold type.