- RUNCO International OWNER'S OPERATING MANUAL 1080p Digital Light ProcessingTM Projector and Digital High Definition (DHDTM) Controller VX-44d, VX-55d
Table Of Contents
- TWO YEAR LIMITED WARRANTY
- Safety Precautions
- 1. Introduction
- 2. Controls and Functions
- 3. Installation
- 3.1 Remote Control
- 3.2 Quick Setup
- 3.3 Installation Considerations
- 3.4 Installing the Projection Lens
- 3.5 Installing the Optional CineWide Lens Mount
- 3.6 Mounting the VX-44d/-55d
- 3.7 Connections to the VX-44d/-55d and DHD Controller
- Connector Panel Access
- Connecting the DHD Controller to the VX-44d/-55d
- Connecting Source Components to the DHD Controller
- RS-232 Controller Connection
- Connecting 12-Volt Trigger Outputs to External Theater Equipment
- Connecting an External IR Receiver to the DHD Controller
- Connecting to AC Power
- 3.8 Turning on the Power
- 3.9 Adjusting the Picture Orientation
- 3.10 Primary Lens Adjustments
- 3.11 Installing and Adjusting the CineWide Anamorphic Lens
- 3.12 Calibrating Projector Input 2 (DVI)
- 3.13 Working With the Lamp
- 4. Operation
- 5. Maintenance and Troubleshooting
- 6. Serial Communications
- 7. Specifications
Operation
62 Runco VX-44d/-55d Owner’s Operating Manual
PRE
L
IMINAR
Y
Figure 4-1. DHD Controller OSD Menu Structure for VX-44d/-55d
Service
Test Video
Grey Bars 1
Grey Bars 2
Color Bars 1
Color Bars 2
Input Names Rename, Restore or Save
Remote Control
Primary
Secondary
Analog Out Mode RGB--, RGB++ or RGBS
Display Device: Configure
Installation
Picture Orientation
Keystone
Lamp Hours (read-only)
Lens
Focus
Zoom
Shift
Auto Setup
HD Format
HD/RGB 1
Auto, RGB or YUV
HD/RGB 2
ADC Bandwidth Auto, 75 MHz, 150 MHz or 300 MHz
YPbPr Input Resolution Auto, 480i/p, 576i/p, 720p or 1080i
Triggers 1 / 2 / 3 / Save
Miscellaneous
Language (currently, English only)
Menu Mode
Timeout
Side Bar Color
Film Mode (SD sources
only)
Resolution
800x600 ... 1400x1050
480i ... 720p ... 1080i
System Reset
Restore Saved Settings
Note: Virtual Cinema is
available only on
VX-44d/-55d projectors
equipped with the CineWide
option (secondary
anamorphic lens).
Input Source
Composite
S-Video 1
S-Video 2
Component SD
HD/RGB 1
HD/RGB 2
HDMI 1
HDMI 2
Aspect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Picture
Brightness
Contrast
Color
Tint
Sharpness
Input Position
Left/Right
Up/Down
Width
Height
Overscan
ISF Presets
Recall ISF Night
Recall ISF Day
Recall/Save Custom 1
Recall/Save Custom 2
Reset Custom 1 & 2 to Factory Default
Information
(read-only)
Serial Number
Hardware
Firmware
Date
Calibration
ISF Night - Display Color Lamp Power
Lamp Intensity
ISF Night - Input Image
Brightness
Contrast
Color
Tint
Sharpness
ISF Night - Input Color
Gain
Offset
Chroma Delay
Phase
Noise Filter
ISF Day - Display Color
Lamp Power
Lamp Intensity
ISF Day - Input Image
Brightness
Contrast
Color
Tint
Sharpness
ISF Day - Input Color
Gain
Offset
Chroma Delay
Phase
Noise Filter
Save ISF Settings Back / Confirm
Output Shift
Left/Right
Up/Down
Width
Height
Save
Splash Configure
Owner Name
ISF Calibrated
ISF Other
Runco/ISF Logo Splash
Screen Timers
(2 ... 60 sec.)
OSD Position
Vert./Horiz.,
Normal/Wide, Height