Model :RFBW01014 Model :RFBE 01014 Model :RFBG 01014 Wall Cabinet Operators’ Manual Manual de Operadora del Gabinete de pared Inspect product prior to installation. Contact info@runfinegroups.com prior to returning product to retailer. Inspeccione el producto antes de su instalación. Póngase en contacto con info@runfinegroups.com antes de devolver el producto al vendedor.
PARTS LIST A. B. C. D. E. F. G. H. I. J. K.
HARDWARE 1. DOOR KNOB / PERILLA DE LA PUERTA 2. DOOR KNOB SCREW (18MM L) / TORNILLO PARA LA PUERTA PERILLA (18MM L) 3. CAM LOCK NUT & BOLT / TUERCA & PERNO CAM 4. WOOD DOWEL / TACO DE MADERA 5. SMALL CAM LOCK NUT & BOLT / PEQUEÑO TUERCA & PERNO CAM 6. DOOR MAGNET AND SCREW / IMÁN Y TORNILLO DE LA PUERTA BLANCA 7. SHELF SUPPORTS / SOPORTA DE ESTANTE 8. WOOD SCREW (12MM L) / TORNILLO DE MADERA (12MM L) 9. PLASTIC ANCHOR & SCREW / BISAGRAS & TORNILLO DE PLÁSTICO 10.
TOOLS REQUIRED (NOT INCLUDED) FLAT HEAD SCREWDRIVER PHILLIPS SCREWDRIVER Por favor, lea las instrucciones antes del montaje. Please read instructions before assembly. Perform assembly on a carpeted surface to prevent scratching. Realizar el montaje sobre una superficie enmoquetada para evitar que se raye. This assembly process require at least two people. Este proceso de montaje requiere al menos dos personas.
ASSEMBLY OF THE SIDE PANELS, FIXED SHELF & BACK TOP CROSS BAR （STEP 1)- #B ASAMBLEA DE LOS PANELES LATERALES, ESTANTE FIJO Y BARRA TRANSCERSAL SUPERIOR TRASERA (PASO 1)- #B Insert wood dowels (4) into the pre-drilled hole of fixed shelf panel (E) & back top cross bar (F), attach fixed shelf panel (E) and back top cross bar (F) to side panel (A) & (B) as shown (Figure 2).
ASSEMBLE TOP PANEL, BOTTOM PANEL AND DOOR MAGNETS（STEP 2) ARMAR LOS PANELES DE LA PARTE SUPERIORES, PANEL INFERIOR Y IMAN DE LA PUERTA (PASO 2) Insert the cam lock bolts (3) into the pre-drilled hole of the top panel (C). Attach the top panel (C) to the side panels (A) & (B) as shown (Figure 4). Inserte los pernos de bloqueo de leva (3) en el agujero previamente taladrado del panel superior (C). Fije el panel superior (C) a los paneles laterales (A) y (B) como se muestra (Figura 4).
ASSEMBLY OF THE BACK PANEL（STEP 3) ASAMBLEA DEL PANEL POSTERIOR (PASO 3) Attached the back panel (H)& (I) to the cabinet using the wood screws (8) as shown (Figure 6). Se adjunta el panel trasero (H) (I) al gabinete con los tornillos de madera (8) como se muestra (Figura 6). Figure 6 ASSEMBLY OF THE DOOR PANEL & DOOR KNOB（STEP 4) ASAMBLEA DE LA PUERTA DEL PANEL DE PUERTA Y MANDO (PASO 4) Screw the door hinges (10) to the door panel(J,K) using the hinge screw (10).
WALL MOUNT INSTALLATION（STEP 5) INSTALACIÓN MONTAJE EN PARED (STEP 5) Locate a desired position on the wall on which to mount the cabinet. If wall studs are located at the exact screw positions of the cabinet cross bars, then mount the cabinet to the wall using mounting screws (9). If the wall behind the cross bars is hollow, then drill through all mounting holes to mark hole positions on the wall. Remove the cabinet from the wall.
