MCA-C5 M U LT I Z O N E C O N T R O L L E R MCA-C5 8 Source Multizone Controller Amplifier User and Installation Manual
SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety - Outdoor Antenna Connection Grounding an Outdoor Antenna If the AM/FM tuner is used with an outdoor antenna, the antenna must be grounded against static charges and voltage surges. Consult the instructions that came with the antenna or contact the antenna manufacturer for proper installation instructions. The diagram gives a general depiction of how an outdoor antenna should be grounded.
TABLE OF CONTENTS Safety Instructions................................................................................................................... 2 Product Overview.................................................................................................................... 5 Controller Illustrations............................................................................................................ 6 Keypad Features........................................................................
product OVERVIEW Thank you for choosing the Russound MCA-C5 multizone controller amplifier to enhance your home with multiroom audio. The MCA-C5 caters to homeowners who want control over their multiroom audio systems with such capabilities as infrared (IR) tools to manage the system from anywhere in the house. Eight source inputs, simplified programming, and user adjustable sound controls make listening to music throughout the home easier than ever.
Controller front Panel Power Switch Red LED behind power indicator Zone LED indicators visible behind cover MCA-C5 M U LT I Z O N E Removable cover to access IR window and USB port CONTROLLER Front Panel Red IR LED (talk-back) IR Receiver Window USB Port for Programming Programming Center USB 2.0/1.
Controller Rear Panel Home Theater 12 VDC Trigger Activates source power management when sharing sources with home theater Zone 12V Triggers 12VDC 100ma outputs ready when corresponding zone is active Controller ID Switch Set ID for multiple controller configurations or firmware updates RNET Link - Links multiple controllers and RNET sources Speaker Outputs - Connect 4-8 Ohm speakers for each of the first six zones Serial Interface RS232 ports for firmware updates and communication Keypad Ports - RJ-45
Keypad Features MDK-C5 Keypad The main menu (Home) options include: Now Playing, Sources, Alarm, Sleep Timer, Party Mode, Do Not Disturb, and Settings. The Settings menu includes the audio, clock, display, and installer options. The audio settings include bass, treble, balance, loudness, and turn on volume. The MDK-C5's buttons and menus allow the user to easily find and control music sources and to make changes to system settings and room audio levels.
Keypad usage Basic Operation Main Menu - Favorites Turn on the zone - Press the power button on the keypad or press power on the SRC-C5 remote control to turn on the zone and hear music. The zone will default to the last playing source before being turned off. Press and hold the power button (when ON) to turn on all the keypads. Turn off the zone - Press the power button on the keypad or press the power button on the SRC-C5 remote control to turn off the keypad and music.
Keypad usage Main Menu - Sleep Timer Main Menu - Settings You can set the timer so the zone turns off in one of the following increments: 15, 30, 45, or 60 minutes. Audio - From the home screen, scroll to and select "settings," and choose "audio settings." You’ll see items to adjust, such as bass, treble and balance. Each selection has its own screen and shows levels for real-time adjustments.
SRC-C5 Remote Control LED - IR Indicator. Set - Program sequences VID / DVD / TV - Use these keys to select a local device. Power - Turn the selected source on or off. Russound Zone Control - Activates control of Russound system controller and keypads, and its connected sources. Numeric Keys - Directly enter channels (e.g. 09 or 31). Input - Switch the TV’s, VCR’s, SAT’s or DVD’s input to view TV or video programs. Without a local device selected, toggles through sources on keypad.
installation OVERVIEW Ventilation Requirements Important Considerations Important: The MCA-C5 should be situated so that its location or position does not interfere with its proper ventilation. Do not block vents above or to the sides of the unit, as it requires ventilation for proper operation. Do not expose to excessive dust, and do not allow dust to build up on the unit and block vent holes. Do not place the MCA-C5 above or below a heat-generating component such as an audio amplifier.
Installation Guide Wiring Rack Mount Installation Route CAT-5e cable between the keypad locations and the controller. Terminate all CAT-5e cables with an RJ-45 connector using the T568A wiring standard configuration. Utilize a UL/CSA approved electrical box at the keypad (double-gang at least 32 cu. in.) and controller locations. Using connector specific wall plates at the controller location will better organize all of the incoming cables.
Keypad rear CAUTION Mounting screws must be handtightened. Over-tightening the mounting screws can cause the buttons to jam and malfunction.
Keypad IR Connections External IR Connection to MDK-C5 Keypad The MDK-C5 keypad has an External IR Receiver In terminal for connecting an external IR Receiver such as the Russound 858, SaphIR 862 Eye, or SaphIR 860 Phantom. AM/FM Front IR 11:30 AM Off On Use 2 twisted pair wire with one pair connecting GND (GROUND) and IR (SIGNAL) and the other pair connecting ST (STATUS) and V+ (+12VDC). Do not connect the shield to the IR receiver terminals.
Keypad Color Plate Conversion MDK-C5 Color Plate Conversion You will need both small straight and Phillips head screwdrivers to change the color plates on the keypad. The Bezel Molding and the Trim Plate will be switched for the new color plates. 5. Remove the Bezel Molding by gently pressing in each of the 4 locking tabs (2 per side) while pushing it away from the metal frame. 1. If installed, remove the MDK-C5 keypad from the wall. Gently pull the Trim Plate off the mounting plate.
COntroller / Keypad connection Controller / Keypad Connection The MDK-C5 keypad is designed for use with the C-Series controllers, and connects to a keypad port near the top left on the rear of the controller. These RJ-45 ports support MDK-C5 keypads (and up to two UNO-TS2 touchscreens per controller). The eight keypad ports correspond to the eight zones supported by the MCA-C5.
Speaker connections Speaker Output Connections CAUTION: Do not connect L- and R- together. Use four-conductor cable and wire each ground individually. Do not use a common ground. Shorting between terminals will cause damage to the digital amplifier. The MCA-C5 supports speaker outputs for zones 1 through 6. These 40 watt per channel stereo speaker level outputs have high-current two-channel digital amplifiers. Each speaker connection requires a 4 to 8-ohm load.
Source connections RNET Source Data Connections Source Audio Connections The RNET Link In and Link Out can be used to connect the MCA-C5 to other specified Russound RNET-enabled source equipment. The connection is made using a CAT-5e patch cable from the Link Out of the controller and into the Link In of the RNET-enabled source. Another CAT-5e patch cable can be used to link out of that source and link into another RNET-enabled source in the system.
IR Connections IR Connections Routed IR Outputs These six routed IR emitter outputs are supported by the MCA-C5 IR engine and support IR pass-through. They are also carried by the RNET Link cable to additional controllers. Attach the end of the IR emitter with the 3.5mm plug to the IR emitter port. Remove the adhesive back at the other end of the emitter and attach the emitter over the source component’s IR window.
Multiple Controller INstallation Linking Multiple Controllers Controller ID Switch Settings The RNET Link In and Link Out can be used to connect two or more (up to 6) MCA-C5 controllers (does not support CAV6.6, CAM6.6 or CAA66 controllers). The connection is made using a CAT-5e patch cable from the Link Out of the first controller and into the Link In of the next controller. Along with RNET data signals, the RNET Link In and Link Out port passes source IR signals.
Trigger Connections Zone 12VDC Trigger Outputs There are eight zone 12VDC Triggers which are located under the routed IR outputs. The 3.5mm mini port provides 12VDC 100mA when the corresponding zone is turned on and is disengaged when the zone is turned off. The trigger can be used to engage any 12VDC trigger device or component that does not exceed 100mA, such as the Russound R235LS amplifier. The connections for the trigger outputs are made using a two-conductor cable with 3.
Trigger Connections Page Trigger IN The page trigger can be used to trigger a page event. The 12VDC trigger input overrides signal sensing and selects the audio input from Source 8 (if included in page event) and sends it to any zone that does not have page disabled or that is not in Do Not Disturb mode. Do not use the page trigger input if there is a regular audio source connected to Source 8. Tip - Pos (+) 3.
Trigger Connections Home Theater Triggers These triggers are used to integrate with home theater systems that can provide a 12 volt trigger. The MCA-C5 can be used to power manage sources that are being shared with the home theater system. For example, the power management system will check to see the state of the home theater before powering down source gear. Refer to the sample configuration diagram on the next page for connections.
Trigger Connections Home Theater Receiver 12V trigger cable MCA-C5 Controller Power strip Power cord Power cords ACT-1 120VAC outlet DVD CD Player Tuner 12V trigger cable Loop to other 12VDC triggered device Sample Configuration - Home Theater Trigger Russound MCA-C5 User and Installation Manual 25
Additional Connections RS232 Serial Interface AM/FM Antenna Connections: The RS232 serial port is located on the back of the MCA-C5 and use a DB-9 cable connection. The MCA-C5 supports RS232 communication with various third-party automation systems through the RS232 port. The RS232 port supports a standard 19.2 kHz baud rate, This port can also used for firmware updates. Firmware update protocol is available on the Document Center at www. russound.com.
SCS-C5 Configuration Software Programmable options with SCS-C5 software The necessary software (SCS-C5) to program and configure the system is available via download from the Doc Center at www.russound.com. With your PC laptop, you can configure the system prior to connecting with the MCA-C5 controller. The software has a Source Setup Wizard to aid in the setup and basic configuration of the sources. Once configured, the system information can be saved to a file.
system Start up Troubleshooting Start up 1. Make connections of sources, speakers and keypads to the controller(s). 2. In a multiple controller configuration, set the controller IDs to unique numbers. Use CAT-5e linking cables of no more than 18 in (45.7 cm) to link the controllers. 3. Plug in and power the sources and controllers. 4. The left LED showing power on the front panel of each controller should be lit. 5. Configure the system using the SCS-C5 software.
SRC-C5 Remote Control - Programming Programming a Device Searching for your Code To control Universal TV, VCR or DVD, Cable or Satellite Receivers, Amplifier or tuner, and Auxiliary devices, follow these steps. Before proceeding, find the codes for the devices you want to program in "Manufacturer’s Codes" in this manual. If your device does not respond to the remote after trying all codes listed for our brand, or if your brand is not listed, try searching for your code: 1. 2. 3. 4.
Remote Control - Programming Using Learning Deleting a single learning key The SRC-C5 includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g., VCR Tracking Up or Down). The following precautions apply: • The original remote control must be in working order and available for learning to work properly. • Learned keys are mode specific, so each one can store a unique function for each mode.
SRC-C5 Remote Control Device Codes MANUFACTURER’s CODES Setup Codes for Audio Amplifiers Accuphase 30382 Acurus 30765 Adcom 30577, 31100 Aragon 30765 AudioSource 30011 Bel Canto Design 31583 Bose 30674 Carver 30892 Curtis Mathes 30300 Durabrand 31561 GE 30078 Harman/Kardon 30892 JVC 30331 Kenwood 30356 Klipsch 30765 Left Coast 30892 Lenoxx 31561 Luxman 30165 Marantz 30321, 30892 Mark Levinson 31483 Mondial 30765 Nakamichi 30321 NEC 30264 Optimus 30300, 30395 Parasound 30246 Philips 30892 Pioneer 30013, 3030
SRC-C5 Remote Control Device Codes Setup Codes for Cable Converters (continued) Comtronics 00040 Contec 00019 Coolmax 00883 Digi 00637 Director 00476 Dumont 00637 Eastern 00002 Emerson 00797 Everquest 00015, 00040 Focus 00400 Garrard 00153 GC Electronics 00056, 00207 Gemini 00015, 00797 General Instrument 00003, 00011, 00276, 00476, 00810 Global 01327 GoldStar 00040, 00144 Goodmind 00797 Hamlin 00009, 00020, 00034, 00259, 00273 Hitachi 00011 Hytex 00007 Jasco 00015, 00153, 00315 Jerrold 00003, 00011, 00012
SRC-C5 Remote Control Device Codes Setup Codes for Video Accessories (continued) Northgate 01272 Panasonic 01120 Pinnacle Systems 01268 Pioneer 01010 Princeton 00113, 00295 Rabbit 00081 Ricavision 01272 Roku 01486 Samsung 01190, 01490 Sensory Science 01126 Sharp 01010 SMC 01456 Sony 01272, 01324, 01364 Stack 9 01272 Streamzap 01309 Systemax 01272 Tagar Systems 01272 TeleCaption 00171 Toshiba 01272 Touch 01272 Viewsonic 01272, 01329 Vizio 01126 Voodoo 01272 ZT Group 01272 Setup Codes for DVD Players Adcom
SRC-C5 Remote Control Device Codes Setup Codes for Satellite Receivers (continued) Jerrold JVC LG Magnavox Matsushita Memorex Mitsubishi Motorola NEC Next Level Panasonic Paysat Philips Pioneer Proscan Proton RadioShack RCA Samsung Sanyo Sharp Sony Star Choice Tivo Toshiba UltimateTV Uniden US Digital USDTV Voom Zenith 00869 00492, 00775, 01170, 01775 01226, 01414 00722, 00724 00214, 00340, 00500 00724 00749 00856, 00869 00496, 01270 00869 00214, 00247, 00340, 00500, 00701 00724 00099, 00722, 00724, 0074
SRC-C5 Remote Control Device Codes Setup Codes for TVs (continued) Sylvania Princeton Prism Proscan Proton Pulsar Quasar Symphonic Tandy Tatung Technics Technol Ace Techview Techwood Teknika 10700, 10717 10051 10047, 10466, 11347, 11447, 11922 10003, 10052, 10178, 10466 10017, 10019 10051, 10055, 10165, 10250, 10650, 11919, 11924 RadioShack 10019, 10030, 10032, 10039, 10047, 10056, 10154, 10165, 10178, 10180, 11904, 11920 RCA 10018, 10019, 10038, 10047, 10090, 10135, 10679, 11047, 11147, 11247, 11347, 1
SRC-C5 Remote Control Device Codes Setup Codes for VCRs (continued) Optimus 20037, 20048, 20058, 20104, 20162, 20432, 20593, 21048, 21062, 21162, 21262 Optonica 20062 Orion 20002, 20184, 20209, 20295, 20479, 21479 Panarex 21950 Panasonic 20035, 20077, 20162, 20225, 20226, 20227, 20367, 20614, 20616, 21035, 21062, 21162, 21262 Pansat 21950 Penney 20035, 20037, 20038, 20040, 20042, 20054, 20240, 21035, 21237 Pentax 20042, 20105 Philco 20035 Philips 20035, 20062, 20081, 20110, 20618, 20739, 21081, 21181, 21381
TECHNICAL SPECIFICATIONS MCA-C5 Multizone Controller Dimensions: Weight: Power Supply: Fuse Rating: Power Consumption: Frequency Response: Watts per channel: Total Harmonic Distortion: Signal to Noise Ratio: Audio Source Inputs: Audio Zone Outputs: Trigger Outputs: Trigger Inputs: Speaker connection: Keypad ports: IR Outputs: Communication ports: Frequency Range: Antenna impedance AM: Impedance FM: Sensitivity: Image rejection: S/N ratio: MDK-C5 Keypad 17"W x 3.5"H x 17.2"D (43.
WARRANTY Warranty The Russound MCA-C5 Controller Amplifier and MDK-C5 Keypad are fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound.
Notes Russound MCA-C5 User and Installation Manual 39
MCA-C5 8 Source Multizone Controller Amplifier User and Installation Manual ©2008 Russound. All rights reserved. All trademarks are the property of their respective owners. Specifications are subject to change without notice. Russound is not responsible for typographical errors or omissions. Russound, Inc. 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 email: tech@russound.com www.russound.