Use and Care Manual

TECHNICAL DATA AAC-09
AMERICAN ACCENTS
DECORATIVE KITS
Form: GDH-394
Rev.: 072914
1
.DESCRIPTION AND USES .
Rust-Oleum
®
American Accents
®
base coat spray provides
a durable metallic finish for use on interior/exterior metal,
wood, plaster, masonry, wicker and unglazed ceramic
surfaces. The base coat sprays dry to a smooth satin
finish. Not for use on galvanized metal. The antique
topcoat is designed to add antique quality to bare wood
and previously painted wood, as well as metal, plaster,
masonry and unglazed ceramics. It is suitable for interior
use or for use in a covered outdoor location. This easy 2-
step process does not require priming.
.PRODUCTS .
SKU Description
7981955 Antique Gold
7985955 Light Patina
7983955 Antique Pewter
202732 Antique Copper
.PRODUCT KIT INCLUDES .
Metallic Base Coat Spray
½ Pint Antique Topcoat
Foam Brush
Abrasive Pad
Idea Booklet
.PRODUCT APPLICATION .
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperatures are between 50-90ºF (10-
32ºC) and humidity is below 65% to ensure proper drying.
Do not apply to surfaces, when heated, exceed 200ºF
(93ºC). Avoid spraying in very windy and dusty conditions.
Cover surrounding area to protect from spray mist.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with soap and water,
or other suitable cleaning method. Rinse with fresh water
and allow to thoroughly dry. Remove loose paint and rust
with a wire brush or sandpaper. Lightly sand glossy
surfaces.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
.PRODUCT APPLICATION (cont.) .
APPLICATION
Aerosol Base Coat - Shake can vigorously for one minute
after the mixing ball begins to rattle. If mixing ball fails to
rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake
often during use. Hold can upright 10-14” from surface and
spray in a steady back-and-forth motion, slightly
overlapping each stroke. Keep the can the same distance
from the surface and in motion while spraying. Apply a
light coat followed by a heavier wet coat for the best
appearance. Do not use near open flame. The base coat
dries in 30 minutes. Once the base coat has dried, gently
rub the metallic base with the abrasive pad to promote
adhesion between coats.
Antique Topcoat – Before applying the antique topcoat,
dampen paper towels or lint-free rags with fresh water and
set aside. Stir the topcoat thoroughly to ensure any settled
pigment is re-dispersed. Working in small areas (6”x6”),
use the sponge brush to wipe on the antique coating. Be
sure to apply in all crevices and grooves. Do not apply too
heavily to avoid drips. Immediately with the water towel or
rags, begin to quickly wipe off the topcoat without
removing from the crevices. Use a blotting motion to
remove excess topcoat pooled in the crevices and
grooves. The towel will not remove much antique coating
as it absorbs excess quickly as the towel becomes
saturated. Change towels frequently and allow the topcoat
to collect in the crevices to enhance the antique effect.
Extend the blotting beyond the painted area by about 1
inch to feather the edges and avoid striping. Once the
desired look has been achieved, proceed to the next area
and repeat the process.
DRY AND RECOAT TIMES
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. The
aerosol base coat dries to touch in 20 minutes, to handle
in 1 hour and fully dry in 24 hours. The antique topcoat
dries to touch in 20 minutes and can be recoated after 1
hour.
CLEAN-UP
Aerosol Base Coat - When finished spraying, clear spray
valve by turning can upside down and depressing spray
button for 3-5 seconds. If the valve clogs, twist and pull off
spray tip and rinse in a solvent such as mineral spirits. Do
not insert any object into can valve opening. Clean-up wet
paint with xylene or mineral spirits. Properly discard empty
container. Do not burn or place in home trash compactor.
Antique Topcoat – Clean brush immediately with soap and
water. Clean-up dried paint with xylene or mineral spirits.