Use and Care Manual
TECHNICAL DATA ATO-63
ACRYLIC ENAMEL
Form: GDH-116
Rev.: 070615
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Acrylic Enamel is a premium acrylic finish designed
to provide fast dry, excellent coverage and maximum durability. It
is suitable for use on metal and wood and can be used indoors
or outdoors. Acrylic Enamel features an advanced spray system
that allows you to spray at any angle, even upside down for
those hard to reach areas. A comfort spray tip with a wider finger
pad reduces fatigue caused by continuous spraying.
.PRODUCTS .
SKU (12 ounce spray) Description
248642 Gloss Red
248643 Gloss Black
248644 Gloss Clear (11 oz.)
248645 Gloss White
248647 Flat Black
248648 Semi-Gloss Black
249286 Semi-Gloss White
249290 Satin Espresso
249291 Flat White
249292 Gloss Brown
249293 Satin Canvas
249294 Gloss Green
249295 Satin Nutmeg
249296 Gloss Deep Blue
249297 Satin Deep Green
249298 Satin Ivory
249299 Satin Colonial Red
249300 Gloss Brilliant Blue
249301 Gloss Almond
249302 Gloss Dark Gray
249303 Gloss Yellow
249304 Gloss Orange
249305 Gloss Gray
249306 Satin Wine
..PRODUCT APPLICATION .
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50-90°F (10-
32°C) and humidity is below 85% to ensure proper drying.
Do not apply to surfaces that, when heated, exceed 200°F
(93°C) or galvanized metal. Avoid spraying in very windy
and dusty conditions. Cover surrounding area to protect
from spray mist.
PRIMING
Use of a Rust-Oleum primer provides added corrosion
protection, enhances adhesion and hiding, and is
especially recommended for metal and wood surfaces.
Recommended primers include 7769830 Rusty Metal
Primer, 7780830 Clean Metal Primer, 2067830 Flat Red
Auto Primer, 2081830 Flat Light Gray Auto Primer, and
2089830 Flat Dark Gray Auto Primer.
..PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION
Wash the surface with a commercial detergent, or other
suitable cleaning method to remove dirt. Rinse with fresh
water and dry with a clean cloth. Remove all oil, grease,
wax and petroleum based materials with mineral spirits.
Remove loose paint and rust with a wire brush or
sandpaper. Lightly sand glossy surfaces.
WARNING: If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.eps.gov/lead.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Hold can 10-16" from surface and spray in a steady
back-and-forth motion, slightly overlapping each stroke.
Keep the can the same distance from the surface and in
motion while spraying. Apply 2 or more light coats a few
minutes apart. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 20 minutes, to handle in 1 hour and is
fully dry in 24 hours. Apply a second coat or Clear Coat
within 1 hour or after 48 hours.
CLEAN-UP
Wipe off tip when finished. Clean up wet paint with xylene
or mineral spirits. Properly discard empty container. Do
not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.