Use and Care Manual

TECHNICAL DATA
ROC-149
RUST-OLUEM
®
TRUCK BED COATING
1
Form: ARJ-1791
Rev.: 030619
DESCRIPTION AND USES
Rust-Oleum
®
Truck Bed Coating is the ideal choice for
recoating and restoring worn, unfinished or previously
finished metal truck beds. When used with the Rust-Oleum
®
Truck Bed Applicator Kit (sold separately), this easy to apply
black polymer coating not only helps prevent truck bed
damage caused by scratches, rust and weather, but it also
enhances your vehicle’s appearance. Rust-Oleum Truck
Bed Coating’s fast drying, quick application formula creates
a textured finish that forms to the contours of truck beds and
other areas to cover evenly and protect the entire surface
without the use of a primer. Able to be rolled, brushed or
sprayed on, Rust-Oleum Truck Bed Coating is also ideal for
application on properly prepared surfaces to create a
textured protective coating on running boards, bedrails and
more.
PRODUCTS
SKU
DESCRIPTION (Black)
342668
1-Quart
342669
1-Gallon
PRODUCT APPLICATION
READ ALL DIRECTIONS BEFORE BEGNNING PROJECT
Use on metal truck beds and other metal automotive
surfaces. Not for use on surfaces that will come in direct
contact with heat or high temperatures such as mufflers,
exhaust components and other hot surfaces.
Use outdoors or in a well-ventilated area such as an open
garage when air (ambient) temperature is at a minimum of
55° F (13° C) and relative humidity is below 85%. Do not use
on surfaces that will be exposed to rain or moisture within 24
hours after application.
SURFACE PREPARATION
Bare Metal or Rusted Surfaces: Clean the surface
thoroughly by removing all dirt, rust and grease. Rinse the
area with a mild mix of soap and water and then allow to dry.
For proper adhesion, sand the entire surface to be coated
with the scuff pad included in the Rust-Oleum Truck Bed
Coating Applicator Kit (sold separately) or with 60-120 grit
sandpaper and then remove all sanding dust with a clean
cloth. Protect and mask off all surrounding areas to prevent
paint splatter. For best results, spot prime bare and rusted
surfaces.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION (cont.)
Previously Painted/Coated Surfaces: Use a wire brush to
remove any loose or peeling paint or coatings. Sand the
surface with 60-120 grit sandpaper. Thoroughly rinse the
area with a mild mix of soap and water and then allow to dry
before applying Rust-Oleum Truck Bed Coating.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
APPLICATION
Rust-Oleum Truck Bed Coating is ready to use. Do not thin
or tint. Stir thoroughly before applying. For best results,
apply Truck Bed Coating with Rust-Oleum Truck Bed
Applicator Kit (sold separately) and follow all directions
accordingly. For additional slip resistance or a more textured
appearance, stir 1 Truck Bed Grit pouch into the Truck Bed
Coating. Stir thoroughly to combine the coating and the grit
additive. If you use more than 1 Truck Bed Grit pouch, your
coverage rate will decrease. For maximum durability, apply 2
coats at the recommended coverage rate (see below). The
first coat will dry to touch in 2-4 hours. Apply the second coat
once the first coat is dry to touch.
DRY & RECOAT
Because temperature and humidity fluctuate, allow a
minimum of 24 hours before resuming light duty use of truck
bed coated areas. For heavy duty use, allow 5 days for a full
cure of the truck bed coating.
CLEAN-UP
Clean tools and equipment with soap and water immediately
after use. Clean dried product with Acetone. Clean up over-
spray, drips or spatters with Acetone IMMEDIATELY, as
dried product is very difficult to remove.
Properly dispose of all soiled rags and protect unused
product from freezing.