Use and Care Manual
TECHNICAL DATA ROC-71
UNIVERSAL TOUCH-UP MARKERS
Form: GDH-1167
Rev.: 122118
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Universal Touch-Up Markers are designed to
repair surface scratches and chips on automotive finishes. They
provide fast dry, excellent coverage and maximum durability.
The flexible bottle allows for controlled paint flow.
.PRODUCTS .
SKU (½ ounce) Description
286480 Fast Fix Universal Silver Paint + Primer
286481 Fast Fix Universal Dark Silver Paint + Primer
286482 Fast Fix Universal Off White Paint + Primer
286483 Fast Fix Universal Cool White Paint + Primer
286484 Fast Fix Universal Bright White Paint + Primer
286485 Fast Fix Universal Flat Black Paint + Primer
286486 Fast Fix Universal Gloss Black + Primer
286487 Fast Fix Universal Metallic Black Paint + Primer
286489 Fast Fix Universal Champagne Paint + Primer
286490 Fast Fix Universal Dark Red Paint + Primer
286492 Fast Fix Universal Red Paint + Primer
286493 Fast Fix Universal Gray Paint + Primer
286494 Fast Fix Universal Clear Coat
U5006C Universal Silver
U5007C Universal Dark Silver
U5003C Universal Off White
U5004C Universal Cool White
U5005C Universal Bright White
U5000C Universal Flat Black
U5001C Universal Black
U5002C Universal Metallic Black
U5008C Universal Champagne
U5010C Universal Dark Red
U5011C Universal Red
U5009C Universal Gray
U5013C Universal Clear Coat
U5012C Universal Primer
..PRODUCT APPLICATION .
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 60-90°F (16-
32°C) and humidity is below 60% to ensure proper drying.
Do not apply to surfaces that, when heated, exceed 200°F
(93°C).
PRIMING
If the scratch or chip exposes bare metal or if rust is visible,
use of a Rust-Oleum Automotive Primer (U5012C or
286493) is recommended to provide added corrosion
protection, enhanced adhesion and hiding. Allow primer to
dry 1 hour before applying Rust-Oleum Automotive
Scratch & Chip Repair markers.
..PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION
Wash the surface with a commercial detergent, or other
suitable cleaning method to remove dirt. Rinse with fresh
water and dry with a clean cloth. For best results, remove
all oil, grease, wax and petroleum based materials with
Rust-Oleum Wax & Tar Remover. If necessary, remove
loose paint and rust with a wire brush or sandpaper.
Lightly sand glossy surfaces.
WARNING: If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.eps.gov/lead.
APPLICATION
Shake the bottle well before and during use. Press paint
pen on a hard surface such as a scrap piece of metal to
release the pen valve. Squeeze the bottle to start the paint
flow on the scratch or chip. Use a brush to smooth out the
paint in one direction. Allow the paint to dry for 30 minutes
before applying additional coats. Wait 24 hours after paint
application before applying a clear coat. Do not use near
open flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch and can be recoated in 30 minutes.
Wait 24 hours before using vehicle.
CLEAN-UP
Wipe off tip when finished and replace cap tightly. Clean
up wet paint with acetone or lacquer thinner. Properly
discard empty container.