Use and Care Manual

TECHNICAL DATA
ROC-264
RUST-OLEUM HOME
®
COUNTERTOP COATING KITS
1
Form: ARJ-2551
Rev.: 021423
DESCRIPTION AND USES
Rust-Oleum HOME
®
Countertop Coating is an extremely
durable, easy to use, revolutionary technology that allows
you to coat over a wide variety of countertops without
stripping, sanding or priming. Transform outdated
countertops in 2 steps - simply clean, apply the required
Base Coat + Top Coat system for a brand new look to your
space.
Great for any bare, stained, sealed or previously coated
countertop surfaces such as outdated laminate, ceramic tile,
porcelain tile, melamine, wood and much more.
PRODUCT FEATURES
• 2 Step System
• No stripping, sanding or priming
• Superior adhesion to tough surfaces
• Maximum wear & stain resistance
• Full use after 24 hours
PRODUCTS
SKU
DESCRIPTION
384960
HOME White Tint Base Kit
384961
HOME Deep Tint Base Kit
385183
HOME Ultra White Marble Kit
KIT CONTENTS
1-Quart Countertop Base Coat
1-Quart Countertop Satin Top Coat
1-4 oz. Heavy-Duty Cleaner
1-4 oz. Gray Marble Veining Paint (with Ultra White Marble
kit only)
NOTE: White Tint Base can be applied as is for Ultra White
or tinted prior to application. Two base coats are required
when applying the White Tint Base in Ultra White. Deep Tint
Base must be tinted prior to application.
OTHER SUPPLIES NEEDED (not included in kit)
3/8" Nap Roller Sleeve
1/4" Nap Roller Sleeve
Roller Frame
Painter's Tape
Paint Tray
Bristle Brush
Artist Brush (for marble kit only)
Mist Bottle (for marble kit only)
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
IMPORTANT: All countertops should be tested for
adhesion before coating the entire surface. Clean a small
3”x3”, inconspicuous area, let dry. Apply base coat over
area and allow to dry for 12 hours. Take a utility knife and
make an “X” in the coating down to the surface. Apply a 4”
piece of duct tape over the “X” and press firmly. Remove the
tape with one quick pull. If more than 10% of the coating
comes off, the countertop will need to be sanded with 60-80
grit sand paper before coating the entire surface. After a
successful adhesion test, lightly sand test area before fully
coating.
SURFACE PREPARATION
Rinse or wipe away any dirt and dust. Clean the countertop
with a cleaner degreaser, such as Original Krud Kutter
®
Cleaner Degreaser, 4 oz. cleaner included in kit. Rinse
thoroughly and allow to dry completely. For any areas where
caulk is present, caulk needs to be removed before applying
coating.
NOTE: Failure to follow this preparation method may result
in poor adhesion and possible coating failure.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
SYSTEM APPLICATION
Rust-Oleum HOME
®
Countertop Base Coat is ready to use.
Do not thin. Stir thoroughly prior to use. If using more than
one can of Base Coat, intermix cans together for color
uniformity. Apply when air, material, and surface
temperatures are between 50-90°F (10-32°C) and relative
humidity is below 85%. Use a high-quality bristle brush or
edger to trim the perimeter and hard-to-reach areas. Use a
high-quality, 3/8” nap roller cover to apply an even coat
onto the surface.