SDS
TOPSIDE
PAINT
marine COATINGS
For use above
the waterline on
FIBERGLASS
WOOD
METAL
UV protection
Abrasion &
weather resistant
Excellent leveling
1 QT (32 FL. OZ.)(946 mL)
WARNING!
COMBUSTIBLE
LIQUID AND VAPOR
(See Other Cautions On Back Panel)
spilled material and remove with inert absorbent. Dispose of contaminated
absorbent, container and unused contents in accordance with local, state
and federal regulations.
WARNING: Cancer – www.P65Warnings.ca.gov
KEEP OUT OF REACH OF CHILDREN. INTENTIONAL MISUSE BY
DELIBERATELY CONCENTRATING AND INHALING THE CONTENTS MAY
BE HARMFUL OR FATAL.
We stand behind our products. If you are dissatisfied with this product,
contact Rust-Oleum Technical Services at 1-800-481-4785 for a refund
of the product purchase price. Please note that the performance of
any marine coating depends on many factors outside the control of
Rust-Oleum, including surface preparation, proper application and envi-
ronmental conditions.
VOC < 500 g/L
Rust-Oleum Marine Coatings Topside Paint is an oil-based modified alkyd.
This easy to apply coating provides long-lasting protection and a brilliant
glossy finish on fiberglass, wood or metal. Use above the waterline only.
THINNER & CLEANER: Mineral spirits
APPLICATION TEMP: 50°F - 90°F
SURFACE PREPARATION: Proper surface preparation is key to a smooth, lasting
finish. Surface must be free of dirt, loose paint, rust, oil, grease, wax, soap and any
other foreign matter. Wash with a solution of 2 cups household ammonia per gallon
of water and rinse well. Remove existing mildew with household bleach instead
of ammonia. Never mix ammonia & bleach. Rinse thoroughly and allow to dry.
BARE FIBERGLASS: The entire surface to be painted, regardless of age, must
be thoroughly washed with a fiberglass dewaxer to remove all traces of mold
release agents and wax. Sand the gelcoat with 80-120 grit sandpaper to a dull,
frosty appearance; solvent clean to remove residue. If the surface is in excellent
condition, proceed with the first coat of Topside Paint.
If the surface is rough or imperfections exist, it will have to be repaired. Fill all
nicks and gouges with a fiberglass repair compound; sand smooth when hard, then
solvent clean. Follow with a coat of Rust-Oleum Marine Coatings Primer for Wood
& Fiberglass to smooth the surface and provide a uniform base; sand smooth and
solvent clean. Proceed with the first coat of Topside Paint.
BARE WOOD: Sand the surface smooth with 80-120 grit sandpaper; solvent clean
to remove residue. Fill all screwheads or small holes with a mender; sand smooth
and solvent clean. Apply a coat of Rust-Oleum Marine Coatings Spar Varnish
thinned 10% with mineral spirits to penetrate and seal the porous grain. Follow
directions and dry times on Spar Varnish. Apply one or two coats of Rust-Oleum
Marine Coatings Primer for Wood & Fiberglass until an evenly smooth base
condition is reached; sand each coat with 80-120 grit sandpaper and solvent
clean. Use a tack cloth to remove sanding dust and proceed with the first coat
of Topside Paint. Bare wood that has been epoxied must be thoroughly scrubbed
with an ammonia/water solution then sanded with 120 grit sandpaper and solvent
cleaned. Follow with a coat of Primer for Wood & Fiberglass to smooth the surface
and provide a uniform base; sand well and solvent clean then proceed with the
first coat of Topside Paint.
BARE STEEL: Sandblast to bare metal or abrade with emery cloth or grit wheel.
Solvent wash and allow to dry. Immediately apply one coat of Rust-Oleum Marine
Coatings Primer for Metal; allow to dry 24 hours. Proceed with the first coat of
Topside Paint.
BARE ALUMINUM SURFACES: Wipe the surface free of oil and grease with
solvent. Remove oxidation and abrade the surface with medium grit emery
cloth; remove sanding residue with a tack cloth. Apply one coat of Rust-Oleum
Marine Coatings Primer for Metal; allow to dry 24 hours. Proceed with the first
coat of Topside Paint.
PAINTED SURFACES: If the old paint is in good, sound condition, sand it thoroughly
smooth with 150 grit sandpaper; solvent clean to remove residue, then proceed
with the first coat of Topside Paint. If the old paint is in poor condition, remove it
with a paint & varnish remover or by sanding. Proceed with instructions for the
appropriate bare surface system.
APPLICATION DATA: Stir thoroughly before use. Apply with a brush, roller, con
-
ventional or airless spray. If necessary for brush or roller application, thin with no
more than 5% mineral spirits. For best results on large, smooth surfaces roll out
using a short nap or foam roller followed immediately by leveling off with the tip of
a brush. For conventional spray application, thin 10-15% with Xylene. Apply one
thin, even coat per day. Allow to dry overnight, lightly sand with 220 grit sandpaper,
wipe with a tack cloth and apply a second coat. Applying two or more coats in one
day or applying excessively heavy films (greater than 4 wet mils) will lead to insuf
-
ficient drying of the paint and will yield soft paint films. For airless spray application,
no thinning is required. Dries completely in 24 hours. Do not apply on extremely
humid days (90% humidity or above) or when rain is threatening. Do not apply
in the late afternoon when working outdoors as the wet film may be adversely
affected by dew. When working in cooler temperatures be sure the air and surface
temperatures will remain at or above 50°F for at least 8 hours after application
NON-SLIP DECKS: To provide a safe, slip-resistant texture on decks, add
Rust-Oleum Marine Coatings Anti-Slip Additive to the mixed Topside Paint. Stir
mixture continuously to ensure compound is thoroughly dispersed and remains in
suspension. A minimum of two coats are recommended. No sanding is required
between coats. Allow to dry 24 hours for light use, 3 days for full use. If preferred,
apply a coat of Topside Paint without Anti-Slip Additive to all areas requiring a non-
skid surface then sprinkle or broadcast the Anti-Slip Additive into the wet Topside
Paint. After drying overnight carefully brush-out all loose Anti-Slip Additive and
apply another thin, even coat of Topside Paint to the surface. For decks that have
a pre-molded, non-skid embossment, wash the surface with a dewaxer. Abrade
area thoroughly with bronze wool and solvent clean to remove residue. Apply two
coats of Topside Paint, adding Anti-Slip Additive to the mixture if an improved
non-slip texture is desired.
Contains: Petroleum Distillates. VAPOR HARMFUL. MAY AFFECT THE
BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR
NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. NOTICE:
Reports have associated repeated and prolonged occupational overexpo-
sure to solvents with permanent brain and nervous system damage. Do
not breathe vapors, spray mist, sanding dust or overspray. Ensure fresh
air entry during application and drying. If you experience eye watering,
headache or dizziness or if air monitoring demonstrates vapor/mist levels
are above applicable limits, wear an appropriate, properly fitted respirator
(NIOSH/MSHA approved) during and after application. Follow respirator
manufacturer’s directions for respirator use. Avoid contact with eyes,
skin and clothing. Wash thoroughly after handling. Keep away from heat
and flame. Use only with adequate ventilation. Prevent build-up of
vapors by opening all windows and doors to achieve cross-ventilation.
Close container after each use. FIRST AID: If you experience difficulty in
breathing, leave the area to obtain fresh air. If continued difficulty is expe-
rienced, get medical assistance immediately. In case of eye contact, flush
immediately with plenty of water for at least 15 minutes and get medical
attention; for skin, wash thoroughly with soap and water. If swallowed, do
not induce vomiting. Get medical attention immediately. If spilled, contain
# 206999
11 Hawthorn Pkwy., Vernon Hills, IL 60061
800-481-4785 rustoleum.com
Made in USA | Hecho en E.U.A.
©2018 Rust-Oleum Corporation 336709 0318
Gloss
White
CYAN MAG YELO BLACK SPOTSATINPHX MAC #1460993 05.10.18
PHX 1384006 05.10.18