Use and Care Manual

ManualsBrandsRust-Oleum Porch and Floor ManualsPaint1-gal. Pure White Anti-Skid Satin Coating (2-Pack)

TECHNICAL DATA ROC-18

RUST-OLEUM

PORCH & FLOOR COATING

Form: GDH-80

Rev.: 061713

DESCRIPTION AND USES .

Rust-Oleum

Porch & Floor Coating is an oil-modified acrylic

designed to provide excellent color retention, adhesion and

protection against UV rays, water damage and mildew on both

wood and concrete surfaces. This acrylic formula provides

excellent durability and flexibility, with excellent water repellency

which helps maximize resistance to scuffing, fading, cracking

and peeling. Porch & Floor Coating is recommended for interior

and exterior wood and concrete surfaces. It is not recommended

for use on garage floors.

Use on all species of pressure-treated lumber, pine, fir, Cypress,

Cedar, Redwood, poplar, hickory and other North American

hardwoods. It is suitable for weathered wood to hide the signs of

aging. Can also be used on concrete patios and walkways.

.PRODUCTS .

SKU Description

244054 Dove Gray Satin

244055 Pewter Satin

244056 Clear Tint Base Satin

244057 Dove Gray Semi-Gloss

244058 Pewter Semi-Gloss

244059 Clear Tint Base Semi-Gloss

244847 Dove Gray Gloss

244849 Pewter Gloss

244860 Clear Tint Base Gloss

246744 Anti-Skid Texture Dove Gray

246745 Anti-Skid Tint Base

248137 Anti-Skid Texture Pastel Tint Base

248167 Pure White Pastel Tint Base

248169 Pure White Pastel Tint Base Semi-Gloss

248170 Pure White Pastel Tint Base Satin

..PRODUCT APPLICATION .

SURFACE PREPARATION, WOOD:

Previously Coated Wood, Weathered Wood - Remove all

deteriorated material and coatings. Weathered wood should be

sanded to a sound surface.

Uncoated Weathered Wood - Bare, weathered wood must

be thoroughly cleaned to remove ground–in dirt, mildew, mold

and algae stains, gray, UV-damaged wood fibers, and any other

surface contaminants.

Uncoated, New Wood - The surface must clean of all grease,

oil, dirt, or any other contaminates which may interfere with

adhesion. Use a deck or wood cleaner or other suitable cleaner

and rinse thoroughly. Mold and mildew must be removed with

a chlorinated cleaner or bleach solution. Rinse thoroughly with

fresh water and allow to fully dry. After preparation, sprinkle

water on the bare wood surface. If the water absorbs rapidly,

the surface is ready to be coated. If the water beads, puddles

or is not absorbed, an internal or external barrier exists and

must be eliminated before painting can begin.

..PRODUCT APPLICATION (cont.)

SURFACE PREPARATION, CONCRETE:

Bare Concrete – Proper surface preparation is critical to

performance. Remove all grease, oil, salt and other

contaminants with Rust-Oleum EpoxyShield

Heavy-duty

Degreaser (#214382). Follow label instructions carefully. If

necessary, use a wire brush or sander to remove any loose

or unsound concrete or masonry. For proper penetration and

maximum adhesion, use Rust-Oleum EpoxyShield

Concrete

Etch (#238475). Follow label instructions carefully and allow the

floor to dry completely. Wipe your fingers over the clean, dry

surface. If you see any dust or powder on your fingers, scrubbing

and rinsing until the floor is clean.

Previously Painted, Stained or Sealed Concrete - Remove

any loose or peeling paint, stain or sealer by wire brush or other

suitable method. To ensure proper adhesion, scuff sand the

entire surface. Wash the entire surface with Rust-Oleum

EpoxyShield

Heavy-duty Degreaser (#214382) (diluted as

stated on the label) and scrub the surface using a stiff bristle

brush or broom. Spot etch all exposed concrete surfaces using

Rust-Oleum EpoxyShield

Concrete Etch (#238475). Rinse

thoroughly and allow to dry completely.

WARNING! If you scrape, sand or remove old paint from

any surface, you may release lead paint dust. LEAD IS

TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;

ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH

approved respirator to control lead exposure. Clean up

carefully with a HEPA vacuum and a wet mop. Before you

start, find out how to protect yourself and your family by

contacting the National Lead Information Hotline at 1-800-

424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Rust-Oleum Porch & Floor Coating is ready to use. Do not thin.

Apply only when air, material, and surface temperatures are

between 50-90°F (10-32°C) and the relative humidity is below

85%. Do not apply outdoors if rain is expected within 24 hours.

This product is self priming. For the most durable finish apply two

coats at the recommended coverage rate. First coat will dry to

touch in 1-2 hours. Allow a minimum 4-6 hours dry time before

re-coating. Apply with a high quality nylon/polyester bristle brush,

short nap paint/stain pad or roller or an airless sprayer (do not

use a pump sprayer). Brushing is the preferred method,

especially for rough sawn wood. When rolling or spraying, make

sure to back-brush along the grain. This will eliminate any drips,

runs, uneven coverage or surface puddles. To minimize lap

marks maintain a wet edge. If using more than one gallon,

intermix all cans of the same product to ensure color uniformity.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA ROC-18 RUST-OLEUM® PORCH & FLOOR COATING DESCRIPTION AND USES ..PRODUCT APPLICATION . Rust-Oleum® Porch & Floor Coating is an oil-modified acrylic designed to provide excellent color retention, adhesion and protection against UV rays, water damage and mildew on both wood and concrete surfaces. This acrylic formula provides excellent durability and flexibility, with excellent water repellency which helps maximize resistance to scuffing, fading, cracking and peeling.
PAGE 2
TECHNICAL DATA RUST-OLEUM PORCH & FLOOR COATING ..PRODUCT APPLICATION (cont.) Note: Painted floors may be slippery when wet. If desired, Rust-Oleum EpoxyShield Anti-Skid Additive (#214383) may be added to the mixed coating. DRY TIMES Dries to the touch in 1-2 hours. Longer dry time is required in cooler temperatures and at higher humidity. Surface is ready for light foot traffic after 24 hours. Allow 72 hours before returning furniture to porch/deck floor. Avoid dragging furniture across the surface.
PAGE 3
TECHNICAL DATA RUST-OLEUM® PORCH & FLOOR COATING PHYSICAL PROPERTIES . PORCH & FLOOR COATING Resin Type Water-based Urethane Modified Acrylic Pigment Type Titanium Dioxide and Colorant Dispersions Solvents Water Per Gallon 8.6-10.4 lbs Per Liter 1.03-1.25 kg By Weight 31.2- 43.4% By Volume 27.9-30.4% Weight Solids Volatile Organic Compounds 100 g/l (0.83 lbs./gal.