Specification

ManualsBrandsRust-Oleum RockSolid ManualsPaint1 gal. Gunmetal Metallic Garage Floor Kit

RockSolid® Metallic Floor Coating Installation Instruction Sheet

Read instructions carefully before starting project. For more details and application tips go to rustoleum.com/rocksolid

Coverage

Each Polycuramine® pouch covers up to 125 sq. feet.

Indicated Use

For covered garages only; not intended for areas exposed to direct sunlight.

DO NOT leave container in direct sunlight.

Ideal Application

Temperature

Apply when air temperature is 40-90°F and relative humidity is below 80%.

DO NOT apply coating if temperatures are expected to drop below 40°F for 24-48 hours after

application.

Minimum Floor

Temperature

Minimum floor temperature for coating is 40°F.

RockSolid

Product Support

For questions or comments, call our toll-free Product Support 1-866-765-4474

SAFETY INFORMATION

WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT

WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure, and clean

up carefully with a HEPA vacuum and wet mop. For more information, contact the National Lead Information Hotline at 1-

800-424-LEAD or log on to www.epa.gov/lead.

AVOID CONTACT WITH SKIN AND EYES: For skin contact, wash affected area with soap and water and rinse well. For

eye contact, flush with cold water for 15 minutes. If swallowed, do not induce vomiting. Drink 1-2 glasses of water or milk

and contact a physician immediately. KEEP OUT OF REACH OF CHILDREN.

CHECK FOR THE FOLLOWING CONDITIONS PRIOR TO COATING:

Newly Poured

Concrete

If newly poured concrete has not fully cured,

coating will not perform properly.

Allow newly poured concrete to cure for a

minimum of 28 days before coating.

Sealed Concrete

Drip a small amount of water onto floor. If the

water beads, a sealer is present and will need

to be removed.

Once sealer has been removed, proceed to

RockSolid Preparation.

Painted or Coated

Concrete

Remove any loose paint by sanding and

scraping, then test adhesion of remaining

paint:

1. Cut an X through the coating down to the

concrete with a razor.

2. Press duct tape over the X, then remove

with one quick pull.

3. If more than a quarter of the paint comes

off, DO NOT coat the floor with

RockSolid until old paint is completely

removed.

For best adhesion, scuff sand previously painted or

coated floor. Then proceed to RockSolid

Preparation.

Moist Concrete

Apply a 2’ x 2’ sheet of plastic to the garage

floor. Tape down the edges with duct tape and

let set for 24 hours. If water droplets form on

the inside of the plastic or concrete appears

wet (darker in color), moisture is trapped in

the floor and it should not be painted or

coated until moisture issue is resolved.

Use RockSolid Moisture Stop (sold separately)

to remove moisture from concrete.

Loose/Damaged

Concrete

If concrete is loose or chipped, the coating will

not perform properly. Repair damaged areas

before applying RockSolid.

Repair damaged areas before applying

RockSolid.

Summary of content (4 pages)

PAGE 1
RockSolid® Metallic Floor Coating Installation Instruction Sheet Read instructions carefully before starting project. For more details and application tips go to rustoleum.com/rocksolid Coverage Indicated Use Ideal Application Temperature Minimum Floor Temperature RockSolid Product Support Each Polycuramine® pouch covers up to 125 sq. feet. For covered garages only; not intended for areas exposed to direct sunlight. DO NOT leave container in direct sunlight.
PAGE 2
Concrete Preparation* ** 1. Remove oil spots with a scrub brush and a heavy duty degreaser (sold separately). Scrub thoroughly, then rinse. Repeat as needed. 2. Mix concrete etch with 2 gallons of water until dissolved (DO NOT add concrete etch directly to paint). Solution contains a mild citric acid (DO NOT use muriatic acid). 3. Pre-wet entire floor using a hose, then remove pooled water. Use a plastic watering can to evenly distribute etch solution over a 10’ x 10’ section of floor.
PAGE 3
Hoja de instrucciones para la Aplicación del Recubrimiento Metalizado para Pisos RockSolid® Lea atentamente todas las instrucciones antes de comenzar el proyecto. Para obtener más detalles y consejos de aplicación, ingrese a rustoleum.com/rocksolid Cobertura Cada bolsa de Polycuramine® cubre hasta 125 pies cuadrados. Uso Indicado Solamente para ser utilizado en cocheras cubiertas. No está diseñado para áreas expuestas directamente a la luz solar. NO deje el envase bajo la luz solar directa.
PAGE 4
Concreto Preparación* ** 1. Elimine las manchas de aceite con un cepillo de cerdas cortas y duras y un desengrasante de alta resistencia (se vende por separado). Friegue completamente y luego enjuague. Repita tantas veces como sea necesario. 2. Mezcle el ácido para concreto con 2 galones de agua hasta que se disuelva (NO agregue el ácido para concreto directamente a la pintura). La solución contiene un ácido cítrico suave (NO utilice ácido muriático). 3.