Use and Care Manual

TECHNICAL DATA
RSD-01
ROCKSOLID
®
POLYCURAMINE
GARAGE FLOOR COATING KIT
1
Form: GDH-604
Rev.: 013119
DESCRIPTION AND USES
RockSolid
®
Garage Floor Coating Kit is designed to provide
excellent hardness, adhesion and durability on properly
prepared concrete floors. It has excellent resistance to salt,
oil, gasoline and other harsh chemicals. This garage floor
coating contains zero VOC making it environmentally safe
and is packaged in pouches, which reduces waste.
PRODUCT FEATURES
 Low odor and can be applied indoors
 Formulated without the addition of VOC containing
solvent
 One coat system
 45 minute pot life
 Patented Burst Pouch Technology
 96% solids formulation
 Has excellent self-leveling properties
 7 day recoat window without sanding
 Excellent durability in a single coat
KIT CONTENTS
 Polycuramine Burst Pouch (Two part Burst Pouch
Technology U.S. Patent Number 8,381,903 B2)
 Foam Roller
 Decorative Chips
 Concrete Etch
 Instructions
PRODUCTS
SKU
DESCRIPTION
286879
Gray 2.5 Car Kit
286891
Gray 1 Car Kit
286890
Mocha 2.5 Car Kit
286892
Mocha 1 Car Kit
308637
Dark Gray 2.5 Car Kit
308638
Dark Gray 1 Car Kit
318699
Black 2.5 Car Kit
318711
Black 1 Car Kit
PRODUCT APPLICATION
SURFACE PREPARATION
Proper surface preparation is critical to achieve best results.
Scrub heavily soiled areas with RockSolid Heavy Duty
Degreaser or Rust-Oleum Cleaner & Degreaser (sold
separately). Scrub thoroughly, then rinse. Repeat as
needed.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION (cont.)
Use the supplied RockSolid concrete etch per the
instructions to provide the proper surface condition to
ensure proper adhesion. Rinse the floor thoroughly and
allow it to dry completely.
Moisture Testing - New concrete should be allowed to cure
for 30 days before application of any coating. If there is any
doubt about the dryness of the concrete, conduct a test by
simply taping a piece of 4 mil plastic sheet 18x18” on the
bare concrete for 24 hours. Be sure to tape all four sides.
After 24 hours, check the concrete for signs of moisture.
The concrete substrate will be darker if damp. If moisture is
found, allow additional drying time (10-14 days) and repeat
the test.
Testing for Sealer - Check for curing compounds or other
types of sealers by pouring a small amount of water onto the
concrete. If water soaks in, the surface is suitable for
coating. If water beads up on the concrete, the surface is
not porous and a test application is warranted to ensure
proper adhesion will develop. Sanding or mechanical
abrading may be required if proper adhesion does not
develop.
Previously Coated Floors - Previously coated floors need
to be in good condition with proper adhesion to the concrete
substrate. Check the adhesion of the previous coating by
cutting a small X in the coating using a sharp razor knife.
Firmly apply a piece of 5” duct tape over the center of the X
cut, and then pull off with a fast snap. If more than 10% of
the taped area is removed, the original coating is not
bonded well and needs to be removed chemically or
mechanically with a grinder.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
MIXING
MIX ONLY ONE POUCH AT A TIME. Both components and
the environment should be pre-conditioned to a minimum of
40ºF (4ºC) prior to use. Be sure the air and surface
temperatures are at least 5º above the dew point.