Use and Care Manual
TECHNICAL DATA RSD-38
ROCKSOLID
®
2X SOLID STAIN
Form: GDH-1074
Rev.: 030718
1
DESCRIPTION AND USES .
RockSolid
®
2X Solid Stain is a water-based polyurethane
modified acrylic coating designed to resurface wood decks,
docks, concrete patios and walkways. RockSolid 2X Solid Stain
has excellent weather resistance to extend the life of deck and
patio surfaces.
FOR DECKS: For wood and most composite decks.
Follow specific manufacturer’s recommendation before
applying to any composite decking.
FOR CONCRETE: For use on broom swept or porous
concrete surfaces. Do not use on smooth or floated
concrete, fiberglass, tile or metal surfaces.
FOR EXTERIOR USE ONLY AND NOT RECOMMENDED
FOR DRIVEWAYS, GARAGES OR OTHER AREAS WITH
VEHICULAR TRAFFIC.
RockSolid 2X Solid Stain tint base must be tinted at the
store of purchase. DO NOT APPLY IF PRODUCT HAS NOT
BEEN TINTED. RockSolid 2X Solid Stain can be applied
using a ⅜” nap roller, a short nap stain pad or a synthetic
paint brush.
. FEATURES .
One coat application
Ready for use in 24 hours
Excellent water repellency
Algae and mildew resistant coating
.PRODUCTS .
SKU Description
305799 RockSolid 1-Gallon 2X Solid Stain
305831 RockSolid 5-Gallon 2X Solid Stain
COMPANION PRODUCTS ...
SKU Description
312283 RockSolid Deck Start Wood Primer 1-Gallon
60635 RockSolid Deck & Patio Cleaner - 1 Gallon
PRODUCT APPLICATION .
DECK IN ONE DAY METHOD
READ ALL INSTRUCTIONS BEFORE BEGINNING
PROJECT.
REGARDLESS OF AGE OR SURFACE CONDITION,
FAILURE TO FOLLOW ONE OF THESE PREPARATION
METHODS WILL RESULT IN POOR ADHESION AND
POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD
DECKS NEED TO WEATHER AT LEAST 6 MONTHS
BEFORE APPLICATION.
SURFACE PREPARATION
CLEAN: Clean the surface using a deck brush and RockSolid
Deck & Patio Cleaner or standard deck cleaner. The surface
must be clean and free of dirt, grease, mildew and organic
growth. Loose paint needs to be scraped.
LIGHT REPAIRS: For light repairs, secure raised nail heads,
deck screws or loose deck boards. Remove loose splinters and
replace severely damaged or rotting boards.
PRODUCT APPLICATION (cont.) .
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a wet
mop. Before you start, find out how to protect yourself and your
family by contacting the National Lead Information Hotline at 1-
800-424-LEAD or log on to www.epa.gov/lead.
PRODUCT APPLICATION
APPLY ROCKSOLID DECK START WOOD PRIMER: READ
ALL OF THE PRIMER LABEL INSTRUCTIONS CAREFULLY
BEFORE APPLYING.
PRECAUTIONS & TEMPERATURE SAFEGUARDS
DO NOT APPLY IF RAIN IS EXPECTED WITHIN 24 HOURS
OF APPLICATION. Apply when surface and air temperature is
between 40° and 90°F and will remain between 40° and 90°F for
at least 24 hours after application.
APPLICATION
ONE THICK COAT OF ROCKSOLID 2X SOLID STAIN IS
REQUIRED.
Thoroughly mix the material before and during project. When
using more than one container, combine all containers to ensure
color consistency.
Using a 9” NAP roller cover, saturate the roller cover and apply
generously back and forth. Work to a wet edge at all times. Avoid
rolling back into coated areas where drying has begun. Coat 1 to
2 boards at a time.
After coating 1-2 boards, use a putty knife or other straight edge
to remove excess coating between boards. Difficult areas such
as warped or cupped boards will require rolling across the
narrow width of the board as well as the length to ensure
complete coverage.
Allow 2-4 hours to dry to touch. Allow to dry 24 hours if the
temperature is between 50° and 90°F and 48 hours if the
temperature is between 40° and 50°F, before light foot traffic and
replacing furniture. If the surface is tacky or soft, extend the
drying time before putting heavy objects back in place. Full cure
to a hard finish will take approximately 7 days. Drying times may
vary depending on temperature and humidity.
COVERAGE
Up to 250 square feet per gallon (volume after tinting). One coat
is required. Actual coverage may vary based on wood type, age
and surface porosity.
CLEAN-UP
Use mild soap and water.
KEEP FROM FREEZING. CLOSE CONTAINER AFTER
EACH USE TO PRESERVE PRODUCT.
CAUTION: Exterior horizontal surfaces, coated or uncoated,
exposed to sun and warm temperatures can create surface
temperatures not suitable for bare feet or animal paws.