Use and Care Manual

FLOOR COATING TECHNICAL DATA RSP-01
ROCKSOLID
®
POLYCURAMINE
®
PROFESSIONAL FLOOR COATING
Form: TDS-1372
Rev.: 070717
1
.DESCRIPTION AND USES .
RockSolid
®
Polycuramine
®
Professional Floor Coating is
an industrial grade designed to provide excellent
hardness, adhesion and durability on properly prepared
concrete floors. It has excellent resistance to salt, oil,
gasoline and other harsh chemicals. This coating is zero
VOC making it environmentally safe and is packaged in
pouches, which reduces waste.
. PRODUCT FEATURES .

Low odor and can be applied indoors

Formulated without the addition of VOC containing solvent

One coat system

45 minute pot life

Patented Burst Pouch Technology

96% solids formulation

Has excellent self-leveling properties

7 day recoat window without sanding

Excellent durability in a single coat
.PRODUCTS .
SKU Description
322759 Gray
322760 Dark Gray
322761 Mocha
322762 High Gloss Clear
.PACKAGING .
Carton contains 4 – 90 fl oz burst pouches.
PRODUCT APPLICATION .
SURFACE PREPARATION
The concrete surface must be free of all dirt, grease, oil,
fats, and other contamination. Remove surface
contamination by cleaning with RockSolid Heavy Duty
Degreaser , detergent, or other suitable cleaner. Rinse
thoroughly with clean, fresh water and allowed to dry.
Use an appropriate concrete etching solution (do not use
muriatic acid) per the instructions to create the proper
surface condition to optimize coating adhesion. Rinse the
floor thoroughly and allow it to dry completely.
Moisture Testing - New concrete should be allowed to
cure for 30 days before application of any coating. If there
is any doubt about the dryness of the concrete, conduct a
test by simply taping a piece of 4 mil plastic sheet 18x18”
on the bare concrete for 24 hours. Be sure to tape all four
sides. After 24 hours, check the concrete for signs of
moisture. The concrete substrate will be darker if damp. If
moisture is found, allow additional drying time (10-14
days) and repeat the test, or use Rust-Oleum Moisture
Stop (sold separately).
PRODUCT APPLICATION (cont.) .
Testing for Sealer - Check for curing compounds or other
types of sealers by pouring a small amount of water onto
the concrete. If water soaks in, the surface is suitable for
coating. If water beads up on the concrete, the surface
is not porous and a test application is warranted to ensure
proper adhesion will develop. Sanding or mechanical
abrading may be required if proper adhesion does not
develop.
Previously Coated Floors - Previously coated floors
need to be in good condition with proper adhesion to the
concrete substrate. Check the adhesion of the previous
coating by cutting a small X in the coating using a sharp
razor knife. Firmly apply a piece of 5” duct tape over the
center of the X cut, and then pull off with a fast snap. If
more than 10% of the taped area is removed, the original
coating is not bonded well and needs to be removed
chemically or mechanically with a grinder.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
MIXING
MIX ONLY ONE POUCH AT A TIME. Both components
and the environment should be pre- conditioned to a
minimum of 40ºF (4ºC) prior to use. Be sure the air and
surface temperatures are at least 5º above the dew point.
Combine the two components by placing the pouch on the
ground and rolling it from the part A side towards the part
B side like a tube of toothpaste. This will create pressure
in the part A side and force the middle seal to burst,
allowing the two components to mix together. Thoroughly
mix the materials by shaking the pouch back and forth and
squeezing the edges and corners toward the center of the
pouch. Mix for 2-3 minutes.
APPLICATION
Apply only when air, material and floor temperatures are
between 40-90°F (4-32°C). Optimal installation
temperature is 55-90°F (13-32°C). Extreme cold
application temperatures may slow the cure time. Do not
apply in direct sunlight. Do not coat the floor if it is
raining or if extremely damp conditions exist. The concrete
surface must be completely dry at the time of the
application to achieve proper adhesion.