Use and Care Manual

ManualsBrandsRust-Oleum Specialty ManualsPaint11 oz. Frosted Glass Spray Paint (6-Pack)

TECHNICAL DATA SPC-08

SPECIALTY

FROSTED GLASS SPRAY

Form: GDH-329

Rev.: 042114

.DESCRIPTION AND USES .

Rust-Oleum

Frosted Glass Spray creates an etched

glass appearance but permits light to transmit through the

painted surface. It is designed for use on glass doors,

windows, skylights, shower doors, and greenhouses. For a

decorative effect, use a stencil to create an etched look on

mirrors, shower door exteriors, glass accessories, and

more.

.PRODUCTS .

SKU Description

1903830 Frosted Glass

. PAINTING CONDITIONS .

Use outdoors or in a well ventilated area. Use when

temperature is between 50-90°F (10-32°C) and humidity is

below 85% to ensure proper drying. Do not apply to

surfaces, when heated, exceed 200°F (93°C) or surfaces

that are exposed to repeated or continuous water contact,

such as the inside of shower doors. Avoid spraying in very

windy and dusty conditions. Cover surrounding area to

protect from spray mist.

. PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry.

.PRODUCT APPLICATION (cont.) .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Hold can upright 10-

16" from surface and spray in a steady back and forth

motion, slightly overlapping each stroke. Keep the can the

same distance from the surface. Keep the can in motion

while spraying. Apply two or more wet coats a few minutes

apart for best appearance. A wet coat should appear shiny

as it is applied to the surfaces. WAIT 10 MINUTES FOR

FROST EFFECT. Not for outdoor use. Do not use near

open flame.

DRY & RECOAT

Dry and recoat times are based on 70ºF (21°C) and 50%

relative humidity. Allow more time at cooler temperatures.

Dries completely in 5-10 minutes. May recoat at any time.

CLEAN-UP

Clean valve immediately after use by turning can upside

down and depressing spray button for 3-5 seconds (some

paint will be sprayed out, so be careful to not inadvertently

spray yourself or other objects). Clean up wet paint with

xylene or mineral spirits. Properly discard empty container.

Do not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA SPC-08 SPECIALTY FROSTED GLASS SPRAY .DESCRIPTION AND USES . .PRODUCT APPLICATION (cont.) ® APPLICATION Rust-Oleum Frosted Glass Spray creates an etched glass appearance but permits light to transmit through the painted surface. It is designed for use on glass doors, windows, skylights, shower doors, and greenhouses. For a decorative effect, use a stencil to create an etched look on mirrors, shower door exteriors, glass accessories, and more. .
PAGE 2
TECHNICAL DATA PEEL STOP – FROSTED GLASS SPRAY .PHYSICAL PROPERTIES . Physical Properties FROSTED GLASS SPRAY Resin Type Acrylic Lacquer Pigment Type Proprietary Solvents Acetone, N-Butyl Acetate, Xylene MIR 1.40 Max Fill Weight 11 ounces Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80ºF (21-27ºC) and 50% Relative Humidity Approximately 7 sq.ft./can 2 (0.