Use and Care Manual

ManualsBrandsRust-Oleum Specialty ManualsPaint11 oz. Metallic Silver Spray Paint

TECHNICAL DATA SPC-13

SPECIALTY

METALLIC SPRAYS

Form: GDH-333

Rev.: 042914

.DESCRIPTION AND USES .

Metallic sprays provide a rich, brilliant finish on wood,

metal, and more. These sprays add a shiny metallic look

to picture frames, candle holders, holiday crafts, and much

more. This leafing metallic is designed for use on interior

decorative items only.

.PRODUCTS .

SKU Description

1910830 Gold

1915830 Silver

1936830 Brass

1937830 Copper

. PAINTING CONDITIONS .

Use outdoors or in a well ventilated area. Use when

temperature is between 50-90°F (10-32°C) and humidity is

below 85% to ensure proper drying. Do not apply to

surfaces, when heated, exceed 200°F (93°C). Do not

apply to galvanized steel. Avoid spraying in very windy

and dusty conditions. Cover surrounding area to protect

from spray mist.

. PRODUCT APPLICATION .

SURFACE PREPARATION

Remove all dirt, grease, oil, salt and chemical

contaminants by washing the surface with a commercial

detergent, or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sandpaper. Previously

coated surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding to create a surface profile.

Removal of old paint by sanding, scraping or other means

may generate dust or fumes that contain lead. LEAD IS

TOXIC. Contact the U.S.EPA/Lead Information Hotline at

1-800-424-LEAD or log on to www.epa.gov/lead.

.PRODUCT APPLICATION (cont.) .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Hold can upright 10-

16” from surface and spray in a steady back-and-forth

motion, slightly overlapping each stroke. Keep the can in

motion while spraying. Keep the can the same distance

from the surface. Apply two or more light coats a few

minutes apart to avoid drips and runs. Metallic sprays are

not recommended for outdoor use. Do not use near open

flame.

DRY & RECOAT

Dry and recoat times are based on 70ºF (21°C) and 50%

relative humidity. Allow more time at cooler temperatures.

Dries to the touch in 15 minutes, to handle in 30 minutes

and is fully dry in 24 hours. Apply a second coat within 1

hour or after 24 hours. A clear coat finish is not

recommended.

CLEAN-UP

Clean valve immediately after use by turning can upside

down and depressing the spray button for 3-5 seconds

(some paint will be sprayed out, so be careful to not

inadvertently spray yourself or other objects). Clean up

wet paint with xylene or mineral spirits. Properly discard

empty container. Do not burn or place in home trash

compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA SPC-13 SPECIALTY METALLIC SPRAYS .DESCRIPTION AND USES . .PRODUCT APPLICATION (cont.) APPLICATION Metallic sprays provide a rich, brilliant finish on wood, metal, and more. These sprays add a shiny metallic look to picture frames, candle holders, holiday crafts, and much more. This leafing metallic is designed for use on interior decorative items only. .PRODUCTS SKU 1910830 1915830 1936830 1937830 Shake can vigorously for one minute after the mixing ball begins to rattle.
PAGE 2
TECHNICAL DATA PEEL STOP – METALLIC SPRAYS .PHYSICAL PROPERTIES . Physical Properties METALLIC SPRAYS Resin Type Solvent Acrylic Pigment Type Varies with color Solvents Acetone, Toluene, Xylene MIR 1.90 Max Fill Weight 11 ounces Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80ºF (21-27ºC) and 50% Relative Humidity Approximately 10-12 sq.ft./can 2 (0.9-1.