Use and Care Manual

TECHNICAL DATA SPC-15
SPECIALTY
TUB & TILE REFINISHING KIT
Form: GDH-335
Rev.: 031716
1
.DESCRIPTION AND USES .
Tub & Tile Refinishing kit is a 2-part epoxy acrylic
designed to provide excellent adhesion, durability and
color retention in high moisture areas. It is ideal for use to
renew ceramic tile and porcelain, fiberglass, acrylic, cast
iron and steel tubs and sinks. It is not for use on
galvanized steel or flexible plastic. Do not use on areas
exposed to extreme heat such as stovetops, or constant
high humidity environments such as shower stalls. Do not
use in continuous water immersion such as swimming
pools, hot tubs, ponds, or saunas.
.PRODUCTS .
SKU Description
7860519 White
7861519 Almond
7862519 Biscuit
.PRODUCT APPLICATION .
SURFACE PREPARATION
Remove metal drains and hardware. Remove loose paint
and rust with a wire brush or sandpaper. Repair chips and
cracks with a patching compound similar to Liquid Steel
®
.
Remove any mildew with a solution of bleach and water
and rinse thoroughly. Scrub dirty or stained surfaces with
an abrasive cleaner like Comet
®
. Rinse with fresh water
and allow to thoroughly dry. Remove all caulk. Wipe area
clean. Prepare surface with an abrasive pad and Lime-A-
Way
®
, rinse and repeat if necessary. Sand entire surface
with #400/#600 grit wet/dry sandpaper. Vacuum or rinse
away any residue. Wipe surface with a tack cloth
immediately before painting to remove dust.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS
BRAIN DAMGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you sand, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRODUCT APPLICATION (cont.)
APPLICATION
Use when temperature is between 50-90ºF (10-32ºC) and
humidity is below 85% to ensure proper drying. Properly
ventilate the area by opening windows or using fans.
Thoroughly mix Part B to ensure any settled pigment is re-
dispersed. Add Part A to Part B and mix thoroughly for 1
minute. Thin no more than 10% (3 ounces per 1-quart)
with 100% isopropyl alcohol (not rubbing alcohol), acetone
or xylene. If less than a full (1 quart) kit is needed, mix in a
4:1 ratio of base to activator in a separate container. Apply
within 6 hours of mixing.
Brush: Use a fine quality, fine bristle varnish brush. Brush
in one direction only for a smooth surface and feather the
edges as you paint to avoid a hard line between painted
areas. Avoid excessive brushing to ensure an even coat
and smooth finish. Apply two coats, waiting at least 1 hour
between coats. If necessary, a third coat may be applied
the next day with a second kit.
Roller: Use a high quality, ¼” short nap roller made for
kitchen or bath use. Apply two coats, waiting at least 1
hour between coats. Avoid excessive brushing to ensure
an even coat and smooth finish. If necessary, a third coat
may be applied the next day with a second kit. If desired,
conventional HVLP or airless sprayer may also be used.
DRY and RECOAT TIMES
Based on 70ºF (21ºC) and 50% relative humidity. Allow
more time at cooler temperatures. Small bubbles will
appear on the surface as you paint. As the paint dries, the
self leveling properties will eliminate these bubbles. Dries
to the touch in 1 hour. Allow to dry at least one hour before
applying a second coat. Allow to dry 3 days before
exposing to water.
CLEAN-UP
Clean brush and other application tools immediately with
lacquer thinner or isopropyl alcohol. Properly dispose of all
soiled rags. Properly discard empty container. Do not burn
or place in home trash compactor.