SDS

ManualsBrandsRust-Oleum Transformations ManualsAppliance, Tub & Tile Paint46 oz. White Interior Tile Finish Kit

Date Printed: 8/22/2012

4. First-aid Measures4. First-aid Measures

FIRST AID FIRST AID

EYE CONTACT: EYE CONTACT:

Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical

attention. Do NOT allow rubbing of eyes or keeping eyes closed. If exposed to fumes or vapors, flush eyes with plenty of water for

at least 15 minutes. Get medical attention.

FIRST AID FIRST AID

SKIN CONTACT: SKIN CONTACT:

Wash contaminated clothing and decontaminate footwear before reuse. Remove contaminated

clothing. Wash skin with soap and water. Get medical attention.

FIRST AID FIRST AID

INHALATION: INHALATION:

Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get

immediate medical attention. Do NOT use mouth-to-mouth resuscitation.

FIRST AID FIRST AID

INGESTION: INGESTION:

If swallowed, do not induce vomiting. If victim is conscious and alert, give 2 to 4 cupfuls of water or milk.

Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. Treat

symptomatically and supportively.

5. Fire-fighting Measures5. Fire-fighting Measures

Flash Point, °F 100 (Setaflash)

EXTINGUISHING MEDIA: Alcohol Foam, Carbon Dioxide, Dry Chemical, Foam, Water Fog

UNUSUAL FIRE AND EXPLOSION HAZARDS: THIS IS A FAST-CURE POLYURETHANE COATING. When used in spray finish

applications, follow all requirements of OSHA's standard:Spray Finishing Using Flammable and Combustible Liquids, 29 CFR

1910.107. All spray areas should be kept free from accumulation of deposits of combustible residues as practical, with cleaning and

filter change-out conducted daily. All discarded filter pads and filter rolls should be immediately removed to a safe, well-detached

location to fully cure prior to disposal or placed in a water-filled metal container and disposed of at the close of the day's operation.

SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible

autoignition or explosion. Evacuate area and fight fire from a safe distance. Full protective equipment including self-contained

breathing apparatus should be used.

6. Accidental Release Measures

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Isolate the hazard area and deny entry to unnecessary and

unprotected personnel. Remove all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools.

Dispose of according to local, state (provincial) and federal regulations. Do not incinerate closed containers.

7. Handling and Storage

HANDLING: Wash thoroughly after handling. Use only in a well-ventilated area. Avoid contact with eyes, skin and clothing.

Remove contaminated clothing and launder before reuse. Avoid contact with skin and eyes.

STORAGE: Keep container closed when not in use. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks

and open flame. Do not store above 120 ° F. Store large quantities in buildings designed and protected for storage of NFPA Class II

combustible liquids.

8. Exposure Controls/Personal Protection

ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne

levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-

ventilation.

RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must

be followed whenever workplace conditions warrant a respirator's use.

SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin

protection.

Page 2 / 5