Use and Care Manual

TECHNICAL DATA UNI-04
UNIVERSAL
®
GLOSS, FLAT AND MATTE ENAMEL SPRAYS
Form: GDH-144
Rev.: 012915
1
.DESCRIPTION AND USES .
Universal
®
Gloss, Flat and Matte Enamel Sprays provide
long-lasting protection and durability. These sprays apply
easily, provide excellent coverage and dry fast to a tough
attractive finish. Universal Gloss & Flat Enamel Sprays
are ideal for plastic, wood, metal, wicker, and aluminum.
Universal features a comfort grip trigger that reduces
fatigue caused by continuous spraying and an any-angle
tip which allows you to spray at any angle. Some plastics
made of polyethylene such as Little Tikes
®
children’s
products are manufactured in such a way that may hinder
maximum paint adhesion. Test paint in an inconspicuous
area first. Not for use on galvanized metal.
.PRODUCTS .
GLOSS FINISHES Description
245196 Gloss Black
245199 Gloss White
245211 Gloss Cardinal Red
245212 Gloss Cobalt Blue
245213 Gloss Canary Yellow
245214 Gloss Hunter Green
245215 Gloss Espresso Brown
247561 Gloss Sunset Orange
247562 Gloss Crimson Red
247566 Gloss Real Almond
249339 Gloss Slate Gray
284959 Gloss Dark Cherry
284960 Gloss Deep Turquoise
284961 Gloss Tranquil Blue
284962 Gloss Green Citrus
FLAT FINISHES Description
245198 Flat Black
247564 Flat White
MATTE FINISHES Description
282812 Matte Robins Egg
282813 Matte Citron
282814 Matte Harvest Orange
282815 Matte Castle Rock
282816 Matte French Cream
282817 Matte Burlap
282818 Matte Iced Gray
282819 Matte Bittersweet
PAINTING CONDITIONS .
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50-90ºF (10-
32ºC) and humidity is below 65% to ensure proper drying.
Do not use on objects that may exceed 200ºF (93ºC)
surface temperature. Do not apply to galvanized steel.
Avoid spraying in very windy and dusty conditions. Cover
surrounding area to protect from spray mist.
PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with a commercial
detergent, or other suitable cleaning method. Rinse with
fresh water and allow to thoroughly dry. Remove loose
paint and rust with a wire brush or sandpaper. Previously
coated surfaces must be sound and in good condition.
Smooth, hard, or glossy finishes should be scarified by
sanding to create a surface profile.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
ww.epa.gov/lead.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Prior to use, slide off the red safety clip from the
trigger. Hold can upright 8-12” from surface and spray in a
steady back-and-forth motion, slightly overlapping each
stroke. Keep the can the same distance from the surface.
Keep the can in motion while spraying. Apply two or more
light coats a few minutes apart. For best results, apply
several light coats versus one heavy coat. Do not use near
open flame.
DRY & RECOAT
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 30 minutes, to handle in 1 hour, and is fully dry in
24 hours. Recoat within 1 hour or after 48 hours.
CLEAN-UP
When finished spraying, wipe off tip before storing. Clean
up wet paint with xylene or mineral spirits. Properly
discard empty container. Do not burn or place in home
trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.