MSDS

ManualsBrandsRust-Oleum Universal ManualsPaint12 oz. All Surface Gloss Arctic Gray Spray Paint and Primer in One (6-Pack)

Date Printed: 8/12/2013

Ethylbenzene 100-41-4 1.0 20 ppm 125 ppm 100 ppm N.E.

4. First-aid Measures4. First-aid Measures

FIRST AID FIRST AID

EYE CONTACT: EYE CONTACT:

Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical

attention. Do NOT allow rubbing of eyes or keeping eyes closed.

FIRST AID FIRST AID

SKIN CONTACT: SKIN CONTACT:

Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation

develops or persists.

FIRST AID FIRST AID

INHALATION: INHALATION:

Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get

immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to

obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.

FIRST AID FIRST AID

INGESTION: INGESTION:

If swallowed, get medical attention.

5. Fire-fighting Measures5. Fire-fighting Measures

Flash Point, °F -156 (Setaflash)

Extinguishing Media: Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog

UNUSUAL FIRE AND EXPLOSION HAZARDS: FLASH POINT IS LESS THAN 20 °. F. - EXTREMELY FLAMMABLE LIQUID AND

VAPOR!Water spray may be ineffective. Closed containers may explode when exposed to extreme heat due to buildup of steam.

Closed containers may explode when exposed to extreme heat. Vapors may form explosive mixtures with air. Vapors can travel to a

source of ignition and flash back. Isolate from heat, electrical equipment, sparks and open flame. Perforation of the pressurized

container may cause bursting of the can. No unusual fire or explosion hazards noted. Keep containers tightly closed.

SPECIAL FIREFIGHTING PROCEDURES: Full protective equipment including self-contained breathing apparatus should be used.

Evacuate area and fight fire from a safe distance. Water may be used to cool closed containers to prevent pressure buildup and

possible autoignition or explosion. Use water spray to keep fire-exposed containers cool. Containers may explode when heated.

6. Accidental Release Measures

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Contain spilled liquid with sand or earth. DO NOT use

combustible materials such as sawdust. Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Remove

all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools. Dispose of according to local, state

(provincial) and federal regulations. Do not incinerate closed containers. Ventilate area, isolate spilled material, and remove with

inert absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with local, state, and federal

regulations.

7. Handling and Storage

HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.

Use only with adequate ventilation. Follow all MSDS/label precautions even after container is emptied because it may retain product

residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.

STORAGE: Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flame. Contents under

pressure. Do not store above 120 ° F. Store large quantities in buildings designed and protected for storage of NFPA Class I

flammable liquids. Product should be stored in tightly sealed containers and protected from heat, moisture, and foreign materials.

Store in a dry, well ventilated place. Keep container tightly closed when not in use. Keep away from heat, sparks, flame and sources

of ignition. Avoid excess heat.

8. Exposure Controls/Personal Protection

ENGINEERING CONTROLS: Use explosion-proof ventilation equipment. Provide general dilution of local exhaust ventilation in

volume and pattern to keep TLV of hazardous ingredients below acceptable limits. Prevent build-up of vapors by opening all doors

and windows to achieve cross-ventilation. Use process enclosures, local exhaust ventilation, or other engineering controls to control

airborne levels below recommended exposure limits.

RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be

followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with organic

vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed

exposure limits.

Page 2 / 5