Use and Care Manual

TECHNICAL DATA UNI-02
UNIVERSAL
®
METALLIC SPRAYS
Form: GDH-142
Rev.: 032515
1
.DESCRIPTION AND USES .
Universal
®
Metallic Sprays are versatile all-surface paints
that provide a durable protective coating with excellent
resistance to rust, and excellent resistance to abrasion,
fading, chipping, and dulling. These sprays apply easily,
provide excellent coverage and dry fast to a tough
attractive finish. Universal Metallic Sprays are ideal for
plastic, wood, metal, wicker, and aluminum. Universal
features a comfort grip trigger that reduces fatigue caused
by continuous spraying and an any-angle tip which allows
you to spray at any angle. Some plastics made of
polyethylene such as Little Tikes
®
children’s products are
manufactured in such a way that may hinder maximum
paint adhesion. Test paint in an inconspicuous area first.
Not for use on galvanized metal.
.PRODUCTS .
SKU Description
245220 Titanium Silver
245221 Pure Gold
249130 Satin Nickel
249131 Oil Rubbed Bronze
258199 Dark Bronze
261401 Aged Copper
261414 Rustic Mist
267298 White
271471 Flat Chestnut
271472 Flat Burnished Amber
271473 Flat Soft Iron
271474 Flat Antique Nickel
285072 Aged Metallic Rust
PAINTING CONDITIONS .
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50-90ºF (10-
32ºC) and humidity is below 65% to ensure proper drying.
Do not use on objects that may exceed 200ºF (93ºC)
surface temperature. Do not apply to galvanized steel.
Avoid spraying in very windy and dusty conditions. Cover
surrounding area to protect from spray mist.
PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with a commercial
detergent, or other suitable cleaning method. Rinse with
fresh water and allow to thoroughly dry. Remove loose
paint and rust with a wire brush or sandpaper. Previously
coated surfaces must be sound and in good condition.
Smooth, hard, or glossy finishes should be scarified by
sanding to create a surface profile.
PRODUCT APPLICATION (cont.) .
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
ww.epa.gov/lead.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Prior to use, slide off the red safety clip from the
trigger. Hold can upright 8-12” from surface and spray in a
steady back-and-forth motion, slightly overlapping each
stroke. Keep the can the same distance from the surface.
Keep the can in motion while spraying. Apply two or
more moderate coats at moderate speed to avoid drips
and runs. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70ºF and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 30 minutes, to handle in 1 hour, and is fully dry in
24 hours. Recoat within 1 hour or after 48 hours.
CLEAN-UP
When finished spraying, wipe off tip before storing. Clean
up wet paint with xylene or mineral spirits. Properly
discard empty container. Do not burn or place in home
trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.