User Guide

ManualsBrandsRust-Oleum ManualsAutomotive248658-3PK Rust Reformer Spray, 10.25 oz, Black, 3 Pack, 3 Count

SPRAY TECHNICAL DATA ATO

-33

AUTOMOTIVE

RUST REFORMER

Form: GDH-608

Rev.: 052517

].DESCRIPTION AND USES .

Rust-Oleum

Rust Reformer

instantly bonds with rust and

transforms it to a non-rusting, flat-black paintable surface

which prevents future rust. It saves you the effort of

sanding rust all the way down to bare metal.

.PRODUCTS .

10.25-Spray Description

248658 Rust Reformer

.PRODUCT APPLICATION .

PAINTING CONDITIONS

Use outdoors or in a well-ventilated area such as an open

garage. Use when temperature is between 50-90°F (10-

32°C) and humidity is below 85% to ensure proper drying.

Do not apply to surfaces that, when heated, exceed 200°F

(93°C) or galvanized metal. Avoid spraying in very windy,

dusty conditions. Cover surrounding area to protect from

spray mist.

SURFACE PREPARATION

Clean all surfaces with soap and water, rinse and let dry.

Remove loose paint and rust with a wire brush or

sandpaper. Lightly sand glossy surfaces.

WARNING! If you scrape, sand or remove old paint, you

may release lead dust. LEAD IS TOXIC. EXPOSURE TO

LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS

BRAIN DAMAGE, ESPECIALLY IN CHILDREN.

PREGNANT WOMEN SHOULD ALSO AVOID

EXPOSURE. Wear a NIOSH-approved respirator to

control lead exposure. Clean up carefully with a HEPA

vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to

www.epa.gov/lead.

.PRODUCT APPLICATION (cont.) .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Shake often during

use. Hold can 10-16" from surface and spray in a steady

back-and-forth motion, slightly overlapping each stroke.

Keep the can the same distance from the surface. Keep

the can in motion while spraying. For best appearance,

apply two light coats a few minutes apart.

Note: Rust Reformer features an advanced spray system

that allows you to spray at any angle, even upside down

for those hard to reach areas. A comfort spray tip with

wider finger pad reduces fatigue caused by continuous

spraying.

DRY & RECOAT TIMES

Dry times are based on 70°F (21°C) and 50% relative

humidity. Allow more time at cooler temperatures. Allow to

dry for 24 hours. If desired, apply a top coat after 24 hours.

For maximum top coat adhesion and protection, use

Rust-Oleum Stops Rust Paint.

CLEAN-UP

Wipe off tip when finished. Clean up wet paint with xylene

or mineral spirits. Throw away empty can in trash pickup.

Do not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

Summary of content (2 pages)

PAGE 1
SPRAY TECHNICAL DATA ATO-33 AUTOMOTIVE RUST REFORMER ].DESCRIPTION AND USES ® .PRODUCT APPLICATION (cont.) . ® APPLICATION Rust-Oleum Rust Reformer instantly bonds with rust and transforms it to a non-rusting, flat-black paintable surface which prevents future rust. It saves you the effort of sanding rust all the way down to bare metal. .PRODUCTS 10.25-Spray 248658 Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN.
PAGE 2
TECHNICAL DATA AUTOMOTIVE RUST REFORMER SPRAY Physical Properties RUST RFORMER Resin Type Oil modified Alkyd Appearance Opaque liquid Solvents Acetone, Mineral Spirits, N-Butyl Acetate, Xylene MIR 0.8 Max Fill Weight 10.25 ounces Recommended Dry Film Thickness (DFT) Per Coat 1.5-2.5 mils (37.5-62.5µ) Practical Coverage at Recommended DFT (assumes 15% material loss) Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity 8-10 sq.ft.