Technical Specifications

ManualsBrandsRust-Oleum ManualsExterior Oil-Based PaintHigh Performance Black Epoxy Pool & Fountain Paint Kit - 2 gal.

Form: CS1641

Rev.: 011413

TECHNICAL DATA RO-108

HIGH PERFORMANCE

EPOXY POOL PAINT

.DESCRIPTION AND USES .

High Performance Epoxy Pool Paint is designed to provide

long lasting protection for concrete, plaster, gunite, and

fiberglass swimming pools, slides, and spas. While exposure

to sunlight and certain interior lighting conditions causes

fading and chalking of all epoxy type coatings, these changes

are cosmetic in nature only and film integrity and performance

will not be adversely affected. Epoxy coatings will yellow with

age. This is most noticeable with interior applications of white

or light colors which are not subjected to bleaching from

sunlight.

Do Not use over chlorinated rubber, synthetic rubber, vinyl, or

acrylic substrates.

.PRODUCTS .

2-Gallon Kits Description

267919 White

267940 Blue

270182 Black

.PRODUCT APPLICATION .

SURFACE PREPARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with Clean &

Prep Solution or other suitable cleaner. Rinse with fresh water

and allow to dry. Surfaces can also be cleaned using a high

pressure washer at 3,500 psi.

STEEL: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3)

clean to remove loose rust, scale, and deteriorated previous

coatings to obtain a sound rusted surface. For optimum

corrosion resistance, abrasive blast to commercial grade

SSPC-SP-6, with a blast profile of 1-2 mils (25-50μ).

PREVIOUSLY COATED: Previously painted epoxy or bare

fiberglass surfaces must be sound and in good condition.

Smooth, hard, or glossy finishes should be scarified by

sanding or sweep blasting to create a surface profile. The

High Performance Epoxy Pool Paint is compatible with most

coatings, but a test patch is suggested.

GALVANIZED METAL: Remove oil, dirt, grease and other

chemical deposits with Pure Strength

3599 Cleaner/

Degreaser or other suitable cleaner. Remove loose rust, white

rust or deteriorated old coatings by hand or power tool

cleaning or brush off blasting. Rinse thoroughly with fresh

water and allow to fully dry.

CONCRETE OR MASONRY: New concrete or masonry must

cure 30 days before any coatings application. Remove all

loose, unsound concrete. Remove laitance and create a

surface profile by either acid etching with Rust-Oleum

Concrete Saver

108 Cleaning and Etch Solution, or by

grinding. Surface sealers and curing agents must be removed

by grinding.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA RO-108 HIGH PERFORMANCE EPOXY POOL PAINT .DESCRIPTION AND USES .PRODUCT APPLICATION . SURFACE PREPARATION High Performance Epoxy Pool Paint is designed to provide long lasting protection for concrete, plaster, gunite, and fiberglass swimming pools, slides, and spas.
PAGE 2
TECHNICAL DATA HIGH PERFORMANCE EPOXY POOL PAINT .PRODUCT APPLICATION (cont.) EQUIPMENT RECOMMENDATIONS . . MIXING BRUSH: Use a good quality natural or synthetic bristle brush. Both the base and activator components are highly pigmented. Mix each component thoroughly to ensure any settled pigment is re-dispersed before combining the components together. Combine at a 1:1 ratio by volume in a container large enough to hold the total volume. Mix thoroughly for 2-3 minutes. Power mixing is preferred.
PAGE 3
TECHNICAL DATA HIGH PERFORMANCE EPOXY POOL PAINT . PHYSICAL PROPERTIES . High Performance Epoxy Pool Paint Polyamide converted Epoxy Varies with color Exempt halogenated solvent Benzyl alcohol (activator only) 12.5-13.2 lbs. 1.5-1.6 kg 78.9-82.9% 75.7-79.7% Resin Type Pigment Type Solvents Weight per Gallon* Weight per Liter* Solids by Weight* Solids by Volume* * Activated Material Volatile Organic Compounds* <100 g/l (0.83 lbs./gal.) 1:1 Base to Activator (by volume) 5.0-8.