Use and Care Manual

ManualsBrandsRust-Oleum ManualsPaint12 oz. AntiSlip Spray (Case of 6)

TECHNICAL DATA SRT-30

STOPS RUST

ANTI-SLIP SLIP RESISTANT COATING

Form: GDH-627

Rev.: 012315

.DESCRIPTION AND USES .

Rust-Oleum

Stops Rust

Anti-Slip creates a non-skid surface on

concrete, metal and wood. The fast drying formula dries clear

and can be applied to ramps, stairs, railings and more.

Stops Rust Anti-Slip features an advanced spray system that

allows you to spray at any angle, even upside down for those

hard to reach areas. A comfort spray tip with a wider finger pad

reduces fatigue caused by continuous spraying.

.PRODUCTS .

SKU (12 ounce spray) Description

271455 Anti-Slip Slip Resistant Coating

..PRODUCT APPLICATION .

PAINTING CONDITIONS

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50-90°F (10-

32°C) and humidity is below 85% to ensure proper drying.

Do not apply to surfaces that, when heated, exceed 200°F

(93°C). Avoid spraying in very windy and dusty conditions.

Cover surrounding area to protect from spray mist.

SURFACE PREPARATION

Wash the surface with a commercial detergent, or other

suitable cleaning method to remove dirt. Rinse with fresh

water and let dry. Remove loose paint and rust with a wire

brush or sandpaper. Clean concrete surfaces with a

suitable cleaner and water. Rinse and allow to dry. Lightly

sand glossy surfaces.

WARNING: If you scrape, sand, or remove old paint, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN

DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved

respirator to control lead exposure. Clean up carefully with a

HEPA vacuum and a wet mop. Before you start, find out how to

protect yourself and your family by contacting the National Lead

Information Hotline at 1-800-424-LEAD or log on to

www.eps.gov/lead.

PRIMING

Priming is not necessary but additional coats may be required on

porous surfaces such as unfinished wood and concrete.

..PRODUCT APPLICATION (cont.) .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Shake often during

use. Hold can 12-16" from surface and spray in a steady

back-and-forth motion, slightly overlapping each stroke.

Keep the can the same distance from the surface and in

motion while spraying. Apply 2 or more light coats a few

minutes apart. Do not use near open flame.

DRY & RECOAT

Dry and recoat times are based on 70°F (21°C) and 50%

relative humidity. Allow more time at cooler temperatures.

Apply a second coat within 1 hour or after 48 hours. Allow

surfaces to dry for 24 hours before use.

CLEAN-UP

Wipe off tip when finished. Clean up wet paint with xylene

or mineral spirits. Properly discard empty container. Do

not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

Summary of content (2 pages)

PAGE 1
TECHNICAL DATA SRT-30 STOPS RUST® ANTI-SLIP SLIP RESISTANT COATING .DESCRIPTION AND USES . ..PRODUCT APPLICATION (cont.) Rust-Oleum® Stops Rust® Anti-Slip creates a non-skid surface on concrete, metal and wood. The fast drying formula dries clear and can be applied to ramps, stairs, railings and more. APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Shake often during use.
PAGE 2
TECHNICAL DATA STOPS RUST® ANTI-SLIP SLIP RESISTANT COATING PHYSICAL PROPERTIES . STOPS RUST UNIVERSAL BONDING PRIMER Resin Type Proprietary Non-Hazardous Polymer Polypropylene Pigment Type Acetone, Ethyl Benzene, N-Butyl Acetate, Xylene Solvents MIR 2.0 Max 12 ounces Fill Weight Recommended Dry Film Thickness (DFT) Per Coat 1.5-2.5 mils (37.5-62.5µ) Practical Coverage at Recommended DFT Dry Times at 70-80°F (21-27°C) and 50% Relative Humidity 10-12 sq.ft./can (0.90-1.