SDS

Date Printed: 4/14/2016
Stoddard Solvent 8052-41-3 1.0 100 ppm N.E. 500 ppm N.E.
Methyl Ethyl Ketoxime 96-29-7 1.0 10 ppm N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
9. Physical and Chemical Properties
Appearance:
Liquid
Physical State:
Liquid
Odor:
Solvent Like
Odor Threshold:
N.E.
Relative Density:
0.976
pH:
N.A.
Freeze Point, °C:
N.D.
Viscosity:
No Information
Solubility in Water:
Negligible
Partition Coefficient, n-octanol/
water:
N.D.
Decompostion Temp., °C:
N.D.
Boiling Range, °C:
100 - 1,649
Explosive Limits, vol%:
1.0 - 7.0
Flammability:
Supports Combustion
Flash Point, °C:
40
Evaporation Rate:
Slower than Ether
Auto-ignition Temp., °C:
N.D.
Vapor Density:
Heavier than Air
Vapor Pressure:
N.D.
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid temperatures above 120°F (49°C). Avoid contact with strong acid and strong bases.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: When heated to decomposition, it emits acrid smoke and irritating fumes. Contains solvents
which may form carbon monoxide, carbon dioxide, and formaldehyde.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Substance causes moderate eye irritation.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Substance may cause slight skin irritation.
EFFECTS OF OVEREXPOSURE - INHALATION: High gas, vapor, mist or dust concentrations may be harmful if inhaled. Avoid
breathing fumes, spray, vapors, or mist. High vapor concentrations are irritating to the eyes, nose, throat and lungs. Prolonged or
excessive inhalation may cause respiratory tract irritation.
EFFECTS OF OVEREXPOSURE - INGESTION: Irritating to the nose, throat and respiratory tract. Harmful if swallowed.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS: Reports have associated repeated and prolonged occupational
overexposure to solvents with permanent brain and nervous system damage. Contains Titanium Dioxide. Titanium Dioxide is listed
as a Group 2B-"Possibly carcinogenic to humans" by IARC. No significant exposure to Titanium Dioxide is thought to occur during the
use of products in which Titanium Dioxide is bound to other materials, such as in paints during brush application or drying. Risk of
overexposure depends on duration and level of exposure to dust from repeated sanding of surfaces or spray mist and the actual
concentration of Titanium Dioxide in the formula. (Ref: IARC Monograph, Vol. 93, 2010)
PRIMARY ROUTE(S) OF ENTRY: Eye Contact, Ingestion, Inhalation, Skin Absorption, Skin Contact
Page 3 / 5