How to Guide

TECHNICAL DATA INS-02
INSPIRE
PAINT + PRIMER SATIN SPRAYS
Form: GDH-1303
Rev.: 022817
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Inspire Paint + Primer Satin Sprays bring
color to life with long-lasting protection and durability. This
product formula ensures excellent coverage and adhesion
on a variety of interior/exterior surfaces; including wood,
metal, plastic, wicker and more. The Inspire advanced
coating system sprays at any angle, even upside down for
those hard-to-reach areas. The ergonomically-shaped
comfort spray tip has a wider finger pad to reduce finger
fatigue caused by continuous spraying.
TIP: Some plastics made of polyethylene such as Little
Tikes
®*
children’s product are manufactured in such a way
that may hinder maximum paint adhesion. Test paint in a
hidden area first.
.PRODUCTS
SKU (12 ounces) DESCRIPTION
320269 Satin Apple Red
320268 Satin Ink blue
320270 Satin Rustic Orange
297057 Satin Aqua
297063 Satin Blossom White
297000 Satin Canyon Black
297060 Satin Claret Wine
297046 Satin Clear
297058 Satin Colonial Red
297047 Satin Dark Walnut
297021 Satin Eden
296999 Satin Espresso
297004 Satin Granite
297065 Satin Green Apple
296998 Satin Heirloom White
297049 Satin Hunt Club Green
297014 Satin Ivory Silk
297015 Satin Lagoon
297019 Satin London Gray
297013 Satin Magenta
297061 Satin Moss Green
297050 Satin Nutmeg
297020 Satin Oasis Blue
297018 Satin Stone Gray
297025 Satin Summersquash
297022 Satin Warm Caramel
297026 Satin Wildflower Blue
READ ALL DIRECTIONS BEFORE BEGINNING
PROJECT
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50°F (10°C)
and 90ºF (32ºC) and humidity is below 65% to ensure
proper drying. Do not apply to surfaces, when heated,
exceed 200°F (93°C). Do not apply to galvanized steel.
Avoid spraying in very windy and dusty conditions. Cover
surrounding area to protect from spray mist.
* Little Tiles
®
is a registered trademark of The Little Tikes
Company.
PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with a commercial
detergent or other suitable cleaning method. Rinse
thoroughly with fresh water and allow to thoroughly dry.
Remove loose paint and rust with a wire brush or
sandpaper. Lightly sand glossy surfaces to create a
surface profile.
WARNING! If you scrape, sand or remove old paint from
any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH
approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your family by
contacting the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
PRIMING
Use of Inspire Primer provides excellent adhesion and
hiding and is especially recommended for bare wood and
metal.
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Hold can upright 10-16" from surface and spray in a
steady back-and-forth motion, slightly overlapping each
stroke. Keep the can the same distance from the surface.
Keep the can in motion while spraying. Apply two or more
light coats a few minutes apart to avoid drips and runs. Do
not use near open flame.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 20 minutes, to handle in 1 hour, and is fully dry in
24 hours. Apply a second coat or Clear coat within 1 hour
or after 48 hours. Apply clear in 2-3 light coats a few
minutes apart. NOTE: On plastic, maximum paint
adhesion and durability is achieved in 5-7 days.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene
or mineral spirits. Properly discard empty container. Do
not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not stick pin or other
objects into the stem.