Specification

TECHNICAL DATA CHD-07
CHALKED
ULTRA MATTE SPRAYS
Form: GDH-1027
Rev.: 012516
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Chalked Ultra Matte Sprays create an ultra matte
finish with excellent coverage and adhesion on furniture and
home décor. Chalked Ultra Matte Sprays provide one coat
coverage on most surfaces without special surface preparation
or priming. It can be painted or distressed, giving the project a
one of a kind look. It is suitable for use on wood, metal, ceramic,
glass, canvas and more.
Chalked Ultra Matte Sprays feature an advanced spray system
that allows you to spray at any angle, even upside down for
those hard to reach areas. A comfort spray tip with a wider finger
pad to reduce fatigue caused by continuous spraying.
Some plastics made of polyethylene such as Little Tikes
®
children’s products are manufactured in a way that may hinder
maximum paint adhesion. Test this product in an inconspicuous
area to test for compatibility on the surface. Not for use on
galvanized metal.
.PRODUCTS .
SKU (12 ounces) Description
302590 Charcoal
302591 Linen White
302592 Aged Gray
302593 Country Gray
302594 Blush Pink
302595 Serenity Blue
302596 Chiffon Cream
302597 Tidal Pond
302598 Coastal Blue
302599 Matte Clear
.PAINTING CONDITIONS .
Use outdoors or in a well ventilated area such as an open
garage. Apply when the temperature is between 50°F
(10°C) and 90°F (32°C) and humidity is below 85% to
ensure proper drying. Avoid spraying in very windy, dusty
conditions. Cover the surrounding area to protect from
spray mist.
..PRODUCT APPLICATION .
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical
contaminants by washing the surface with soap and water
and let dry. Remove loose paint and rust with a wire brush
or sandpaper. Lightly sand glossy or porous surfaces.
Remove any wax by lightly wiping the surface with mineral
spirits.
WARNING: If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.eps.gov/lead.
..PRODUCT APPLICATION (cont.) .
PRIMING
Priming is not required for most surfaces. For excellent
coverage, use of a Rust-Oleum primer can be used on
surfaces such as bare wood and treated wood.
Recommended primers include:
Painter’s Touch 1908502 Flat Gray
Painter’s Touch 224430T Flat White
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Hold can upright 10-12" from the surface and spray in
a steady back-and-forth motion, slightly overlapping each
stroke. Keep the can the same distance from the surface.
Keep the can in motion while spraying. Apply 2 or more
light coats a few minutes apart. Do not use near open
flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 20 minutes and is dry to handle in 1
hour. May be recoated in 1 hour or after 48 hours. The
finish coat is fully dry in 24 hours. NOTE: On plastic,
maximum paint adhesion and durability is achieved in 5-7
days. Chalked Clear Protective Topcoat can be applied for
added protection. Apply according to the label instructions.
CLEAN UP
Wipe off tip before storing. Clean-up wet paint with xylene
or mineral spirits. Properly discard empty container. Do
not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.
DISTRESSING
This paint can be distressed if desired. To distress the
surface, lightly sand the surface with fine to medium grit
sandpaper or a sanding sponge. Wait 2 hours before
sanding or distressing.