Use and Care Manual

TECHNICAL DATA
SPC-69
RUST-OLEUM
®
SPECIALTY
GLITTER INTERIOR WALL PAINT
1
Form: ARJ-1484
Rev.: 071818
DESCRIPTION AND USES
Rust-Oleum
®
Glitter Brush Paint is an intense glitter finish
that provides multi-dimensional shimmer and sparkle. Can
be applied to drywall, wood, metal, plastic and hardboard.
Formulated to provide a decorative glitter finish to most
surfaces.
PRODUCTS
SKU
DESCRIPTION (Quarts)
323858
Sterling Silver
323859
Harvest Gold
323860
Iridescent Clear
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
SURFACE PREPARATION
Remove loose paint and rust with wire brush or sandpaper.
Lightly sand glossy surfaces. Clean with soap and water,
rinse and let dry. Tape around the area you wish to paint
before beginning.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRIMING
Use of Zinsser
®
Bulls Eye 1-2-3
®
gray primer, to provide
superior adhesion and coverage especially recommended
for bare wood, drywall, or metal. Follow primer
manufacturer’s instructions for topcoat time. After priming
bare wood, sand lightly to smooth surface. For best results,
use the following base coat colors:
Sterling Silver: Zinsser Bulls Eye 1-2-3 gray primer
Harvest Gold: Golden brown primer/paint color
Iridescent Clear: Use any colored or white primer
APPLICATION
For interior use only. Do not apply paint on surfaces which
are exposed to high humidity. Use when temperature is
between 50°F (10°C) and 90°F (32°C) and humidity is below
85% to ensure proper drying.
PRODUCT APPLICATION (cont.)
PAINTING: Rust-Oleum Glitter Brush Paint can be applied
with a roller, brush or paint sprayer. With all application
methods, use uniform thin coats to build glitter film. Stir
paint every couple of minutes during application.
ROLL: Stir thoroughly. Use a 9’’ and 3/8’’ nap roller for best
results. Fully wet roller with paint and remove excess before
applying to wall. Use the roller to spread the glitter evenly.
Roll up and down as well as side-to-side to blend glitter
evenly on the wall.
BRUSH: Stir thoroughly. Use a good quality synthetic
brush. Brush in uniform direction per coat of paint. Apply
each coat of paint in a different direction, alternating each
coat for best results. For example: first coat vertical, second
coat horizontal and repeat. Alternating brushing directions
with successive coats greatly increases coverage. Use light,
even strokes to ensure the smoothest finish.
SPRAY: Stir thoroughly. Mix well in spray gun before
application, do not shake. Use fan pattern for best results.
Dries to recoat in approximately 1-2 hours.
Note: If thinning is necessary, thin 5-10% by weight with
water.
EDGING: For edging tips and techniques visit
www.rustoleum.com.
DRY AND RECOAT TIMES
Based on 77°F (25°C) 50% relative humidity. Allow more
time at cooler temperatures. Dries to the touch in 1 hour, to
handle in 2 hours and fully dry in 2-4 hours. Allow
additional coats to dry 1-2 hours between coats.
COVERAGE
Up to 30 sq. ft. per application with 3/8” nap roller or
synthetic brush. For best coverage results, use the following
base coat suggestions (Sterling Silver: Bulls Eye 1-2-3 gray
primer, Harvest Gold: Golden brown primer/paint color,
Iridescent Clear: Use any colored or white primer). The first
coat does not provide full coverage; full coverage requires 3-
4 coats.
CLEAN UP
Clean brush and other application tools immediately with
soap and water. Follow spray gun manufacturer's
instructions for cleaning equipment.