INSTALL ATION INSTRUCTIONS TRIANGLE HANGER RH ••••••••••••••••••••••••••••••••••••••••• RH024-1.20.
RH 2-3/16" 9-3/8" Ø2-7/8" 6-1/16" 11-7/8" PLEASE NOTE: These instructions are specific to a particular hanger size and type. Adjustments may be needed on your part for changes in specifications and measurements, as well as hanger types that are different than these.
PA R T S A N D T O O L S INSTALL ATI ON I N S T RU CT I ON S Tools Needed Tape Measure Pencil Drill with 1/8”, 1/4” and 3/8” bits, 1” spade bit and Phillips drill bit Short Level Ratchet with 9/16” and 5/8” sockets 9/16” and 5/8” open end and ratcheting wrench Parts Included Hanger Assembly Track Adjustable Spacers Track Stops or Lag Soft Stops Lag Screws Hex Bolts Acorn Nuts Anti-jump Blocks 1” Washers Grabber Screws Door Guide Instructions RH ••••••••••••••••••••••••••••••••••••••••
How Measure Your HAN GtoI N G for TR ACK Door Size INSTAL L ATI O N I N S T RUC T I ON S Doorways Without Trim Door Height Door Opening 1. 1. The exact height of your door opening 2. Door Width = Door Height Adding 2” along either edge of your door opening to the actual width of your door allows your door to cover the door opening plus 2” of wall on either side width of door opening plus 2” Door Opening 2.
HANGER HOLES I N STA L L ATIO N 1. Measuring and Marking Your Hanger Holes IN S T RU C T IO N S 2. Drilling Pilot Holes Door Top • Lay your Door facing UP on saw horses. • Pencil a line 3-1/8” parallel from the Door edge (this marks the proper location for the Hanger edge, near the bottom of the Hanger). • Using your Hanger as a guide, line up the lower portion of your Hanger (down near the two holes) with the line you just made.
AT T A C H I N G H A N G E R IN STAL L ATI O N IN S T RU C T IO N S 1. Installing Your Hanger Assembly To Your Door 2. Tightening Your Hanger Assembly • Thread the Hex Bolts with the Washers through the back of the Door. • Thread the Hanger assembly through the Hex Bolts on the front of the Door. • Holding Hex Bolts in place using a ratchet with a 5/8” socket, lightly tighten your Acorn Nuts by hand.
HANGING TRACK I NSTALL ATION IN STRUCTIONS 2. Hanging Your Track 1. Marking and Drilling Track Holes • Hold up your Track so that the marked line from the previous step is visible through the Track holes. • Mark an intersecting line in the center point of each of the Track holes. • Set the Track down. • Using a drill with 1/4” drill bit, drill out your marked Track holes.* *Be sure you are drilling into wall studs.
I N S TA L L I N G G U I D E I N STAL L AT IO N 2. Door Guide Part 1 1. Installing Your Door • Lift your Door up to your Track at a slight angle. • Carefully rest both Wheel grooves onto the top of the track. • Guide the Door to the resting position. 3. Door Guide Part 2 • Use your level to plumb* your Door. • With the Door in the closed position, place the Door Guide half way into the Door mortise (the groove that runs along the bottom of a wood Door). • Double check that your Door is plumb.
ENJOY INSTAL L ATION INS T RU C T IONS Thank you for your purchase from Rustica Hardware. We hope that your purchasing and installation experience was exceptional. If you need installation assistance or have any feedback, we would love to hear from you. www.RusticaHardware.com 1.800.891.
