Top Mount Reflex Hanger ASSEMBLY INSTRUCTIONS
TOP MOUNT REFLEX HANGER Recommended Tools Level Tape Measure Drill with 1/8”, and 1/4”, Drill Bits and Phillips Bit Pencil Socket Wrench with 9/16” Socket TOP MOUNT REFLEX HANGER Specifications 1-11/16” 5-3/8” 5-3/8” VERSION 2-5/16” 3 1-1/2” 03 3-3/16” 2 RUSTICAHARDWARE.
TOP MOUNT REFLEX HANGER Parts A. B. C. D. E. F. G. H. I. J. VERSION PARTS A. Hanger Assembly B. Lag Screw C. Fastener Screw D. Phillips Screw E. 1” Washer F. Anti-jump Bracket G. Adjustable Spacers H. Door Guide I. Hard Stop & Rubber Bumper J. Track 3 RUSTICAHARDWARE.com 2017 3 03 Use teamwork - We recommend two people for this build.
TOP MOUNT REFLEX HANGER Assembly Instructions NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation. INSTALLATION FOR SQUARE-EDGE DOORS Door Top 1. Place the hanger on the top surface of the door, 2” from the edge of the door side and flush with the door front. Ensure the front of the hanger and the front of the door are facing the same direction (Figure 1).
TOP MOUNT REFLEX HANGER Assembly Instructions NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation. INSTALLATION FOR CURVE-EDGE DOORS 1. Place the hanger on the top surface of the door, 2-3/4” from the edge of the door side and flush with the door front. Ensure the front of the hanger and the front of the door are facing the same direction (Figure 1).
TOP MOUNT REFLEX HANGER Track & Door Installation Instructions FIRST THINGS FIRST Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly. Ensure the track will be installed onto wall studs.
TOP MOUNT REFLEX HANGER Track & Door Installation Instructions 6. Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3). Figure 3 7. Attach one end of the track to the wall with one hard or soft stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten. 8. Repeat step 7 for the other end of the track. Figure 4 9. Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5).
TOP MOUNT REFLEX HANGER Track & Door Installation Instructions 11. Hang the door (Figure 6). Figure 6 DOOR GUIDE INSTALLATION 12. With the door in the closed position, ensure the door is hanging straight using a bubble level. 13. Position the Door Guide part way into the groove in the bottom of the door (Figure 7). SUGGESTION: Use double stick tape on the bottom of the door guide to hold the guide in place. Figure 7 14.
TOP MOUNT REFLEX HANGER Track & Door Installation Instructions ANTI-JUMP GUIDE INSTALLATION FOR SQUARE-EDGE DOORS 17. Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the track. Mark the placement with a pencil. SUGGESTION: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door. 18.
WE LOVE WHAT YOU ARE DOING WITH THE PLACE CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY. WE HOPE YOUR Top Mount Reflex Hanger BRINGS ART AND FUNCTION INTO YOUR LIFE. Designed and crafted entirely in the U.S.A. don’t be a stranger. follow us on social media. support@rusticahardware.