Kingship Hanger ASSEMBLY INSTRUCTIONS
KINGSHIP HANGER Recommended Tools Drill with 1/8”, 1/4”, and 3/8” Drill Bits, 1-1/8” Forstner Bit or 1-1/8” Spade Bit, and Phillips Bit 9/16” and 5/8” Combination Wrench Socket Wrench with 9/16” and 5/8” Sockets Tape Measure Pencil Level KINGSHIP HANGER Specifications 1-7/8” 3/8” 1-15/16” 2-7/8” 3-7/8” � VERSION 12-1/4” 3-11/16” 3 2 RUSTICAHARDWARE.
KINGSHIP HANGER Parts A. B. E. C. F. I. G. J. D. H. K. VERSION PARTS A. Hanger Assembly B. Lag Screw C. Lag Bolt D. Phillips Head Screw E. 1” Washer F. Acorn Nut G. Door Guide H. Hard Stop & Rubber Bumper I. Spacer J. Anti-Jump Bracket K. Track 3 RUSTICAHARDWARE.com 2017 3 03 Use teamwork - We recommend two people for this build.
KINGSHIP HANGER Assembly Instructions NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation. 1. Lay the door with the front facing up on a flat, level surface. 2. Place the hanger on the door (Figure 1). 3. Adjust the placement of the hanger for a 2-3/8” gap between the top of the door and the bottom edge of the wheel.
KINGSHIP HANGER Assembly Instructions 6. Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit (Figure 3). Door Front Figure 3 7. Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole (Figure 4). *A 1-1/8” Spade bit may be used in pace of a Forstner bit. 8. Turn the door over, returning it to the face-up position. Drill all the way through the pilot holes using a drill with a 3/8” drill bit (Figure 5).
KINGSHIP HANGER Track & Door Installation Instructions FIRST THINGS FIRST Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly. Ensure the track will be installed onto wall studs.
KINGSHIP HANGER Track & Door Installation Instructions 6. Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3). Figure 3 7. Attach one end of the track to the wall with one hard stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten. 8. Repeat step 7 for the other end of the track. Figure 4 9. Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5). Tighten all lag screws.
KINGSHIP HANGER Track & Door Installation Instructions � Figure 6 11. Hang the door (Figure 6). DOOR GUIDE INSTALLATION 12. With the door in the closed position, ensure the door is hanging straight using a bubble level. 13. Position the Door Guide part way into the groove in the bottom of the door (Figure 7). SUGGESTION: Use double stick tape on the bottom of the door guide to hold the guide in place. Figure 7 14.
KINGSHIP HANGER Track & Door Installation Instructions ANTI-JUMP GUIDE INSTALLATION 17. Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil. SUGGESTION: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door. 18. Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9). Figure 9 19.
WE LOVE WHAT YOU ARE DOING WITH THE PLACE CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY. WE HOPE YOUR Kingship Hanger BRINGS ART AND FUNCTION INTO YOUR LIFE. Designed and crafted entirely in the U.S.A. don’t be a stranger. follow us on social media. support@rusticahardware.