Stag Hanger ASSEMBLY INSTRUCTIONS
STAG HANGER Recommended Tools Drill with 1/8”, 1/4”, and 3/8” Drill Bits, 1-1/8” Forstner Bit or 1-1/8” Spade Bit, and Phillips Bit 9/16” and 5/8” Combination Wrench Socket Wrench with 9/16” and 5/8” Sockets Tape Measure Pencil Level STAG HANGER Specifications 2” 1-15/16” 1/4” 2-7/8” 1-7/8” 11-1/4” VERSION 3-1/2” 3 3-1/4” 03 3/16” 2 RUSTICAHARDWARE.
STAG HANGER Parts A. E. I. B. C. F. J. G. K. D. H. L. *For use on bi-parting door systems. VERSION PARTS A. Hanger Assembly B. Lag Screw C. Fastener Screw D. Phillips Screw E. 1” Washer F. Anti-jump Bracket G. Anti-jump Block* H. Door Guide I. Adjustable Spacers J. Acorn Nut K. Hard Stop & Rubber Bumper L. Track 3 RUSTICAHARDWARE.com 2017 3 03 Use teamwork - We recommend two people for this build.
STAG HANGER Assembly Instructions NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation. 1. Lay the door with the front facing up on a flat, level surface. 2. Place the hanger on the door (Figure 1). 3. Adjust the placement of the hanger for a 2-3/8” gap between the top of the door and the bottom edge of the wheel. Ensure the side of the hanger is resting 2” from the edge of the door (Figure 2).
STAG HANGER Assembly Instructions 6. Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit (Figure 3). Door Front Figure 3 7. Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole (Figure 4). *A 1-1/8” Spade bit may be used in pace of a Forstner bit. 8. Turn the door over, returning it to the face-up position. Drill all the way through the pilot holes using a drill with a 3/8” drill bit (Figure 5).
STAG HANGER Assembly Instructions FIRST THINGS FIRST Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly. Ensure the track will be installed onto wall studs.
STAG HANGER Assembly Instructions 6. Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3). Figure 3 7. Attach one end of the track to the wall with one hard stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten. 8. Repeat step 7 for the other end of the track. Figure 4 9. Install remaining spacers with lag screws and washers (provided) using a 9/16” socket wrench (Figure 5). Tighten all lag screws.
STAG HANGER Assembly Instructions � Figure 6 11. Hang the door (Figure 6). DOOR GUIDE INSTALLATION 12. With the door in the closed position, ensure the door is hanging straight using a bubble level. 13. Position the Door Guide part way into the groove in the bottom of the door (Figure 7). SUGGESTION: Use double stick tape on the bottom of the door guide to hold the guide in place. Figure 7 14. Install the Door Guide using a 1” phillips screw (provided) and a drill with a phillips bit. VERSION 15.
STAG HANGER Assembly Instructions ANTI-JUMP GUIDE INSTALLATION 17. Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil. SUGGESTION: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door. 18. Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9). Figure 9 19.
WE LOVE WHAT YOU ARE DOING WITH THE PLACE CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY. WE HOPE YOUR Stag Hanger BRINGS ART AND FUNCTION INTO YOUR LIFE. Designed and crafted entirely in the U.S.A. don’t be a stranger. follow us on social media. support@rusticahardware.
