Spoked GARRICK HANGER ASSEMBLY INSTRUCTIONS
SPOKED GARRICK HANGER Recommended Tools Drill with 1/8”and 1/4”Drill Bits, 1-1/8” Forstner Bit or 1-1/8” Spade Bit, and Phillips Bit 9/16” and 5/8” Combination Wrench Socket Wrench with 9/16” and 5/8” Sockets Tape Measure Pencil Level SPOKED GARRICK HANGER Specifications 1-5/8” 4-1/2” VERSION 16-1/4” 3/8” 3 7-3/8” 03 1” 2 RUSTICAHARDWARE.
SPOKED GARRICK HANGER Parts Note: the following instructions are for flat track systems only. Do not attempt to use on tube, box, Bypass, J tracks, or ceiling mount track systems. A. E. I. B. C. F. J. G. K. D. H. L. VERSION PARTS A. Hanger Assembly B. Lag Screw C. Fastener Screw D. Phillips Screw E. 1” Washer F. Anti-jump Bracket G. Anti-jump Block* H. Door Guide I. Adjustable Spacers J. Acorn Nut K. Hard Stop & Rubber Bumper L. Track 3 3 RUSTICAHARDWARE.
SPOKED GARRICK HANGER Assembly Instructions NOTE: Doors using Floor Mount Door Guides will have a groove on the bottom. Ensure this groove is on the opposite end of the Door Hanger Installation. HANGER INSTALLATION Top of Door 1. Lay the door face up on a smooth, level surface. Measure and mark 2-7/8” from the side edge of the door. Measure and mark 1-1/8” from the top edge of the door ensuring lines from both measurements intersect (Figure 1). Side of Door 1-1/8” 2-7/8” Figure 1 2.
SPOKED GARRICK HANGER Track & Door Installation Instructions 4. Drill two pilot holes all the way through the door for each hanger using a drill with an 1/8” drill bit (Figure 3). Door Front Figure 3 5. Turn the door over. Using a 1-1/8” Forstner bit*, drill a 7/16” deep hole into each pilot hole (Figure 4). *A 1-1/8” Spade bit may be used in pace of a Forstner bit. 6. Turn the door over, returning it to the face-up position.
SPOKED GARRICK HANGER Track & Door Installation Instructions FIRST THINGS FIRST Check to see if the floor below the track area is level. If the floor rises more than 1/2” the door may rub or not slide open completely. If the floor is not level, measure from the highest point of the floor surface to the recommended track placement and adjust track placement accordingly. Ensure the track will be installed onto wall studs.
SPOKED GARRICK HANGER Track & Door Installation Instructions 6. Drill out the marked holes using a drill with a 1/4” drill bit (Figure 3). Figure 3 7. Attach one end of the track to the wall with one hard or soft stop, one lag screw, and one washer (provided) using a socket wrench with 9/16” socket (Figure 4). Do not tighten. 8. Repeat step 7 for the other end of the track. Figure 4 03 Figure 5 3 10. Stretch rubber bumper (provided) over hard stop.
SPOKED GARRICK HANGER Track & Door Installation Instructions 11. Hang the door (Figure 6). � Figure 6 DOOR GUIDE INSTALLATION 12. With the door in the closed position, ensure the door is hanging straight using a bubble level. 13. Position the Door Guide part way into the groove in the bottom of the door (Figure 7). SUGGESTION: Use double stick tape on the bottom of the door guide to hold the guide in place. Figure 7 14.
SPOKED GARRICK HANGER Track & Door Installation Instructions ANTI-JUMP GUIDE INSTALLATION 17. Place the Anti-Jump bracket on the door side, moving the bracket up until it is between 1/8” and 1/16” from the bottom edge of the rail. Mark the placement with a pencil. SUGGESTION: Use double stick tape on the back of the anti-jump bracket to hold it in place on the door. 18. Install the bracket to the door edge with 2 phillips screws (provided) using a drill with a phillips bit (Figure 9). Figure 9 19.
WE LOVE WHAT YOU ARE DOING WITH THE PLACE CONGRATULATIONS ON YOUR DECISION TO BRING HOME AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY. WE HOPE YOUR SPOKED GARRICK HANGER BRINGS ART AND FUNCTION INTO YOUR LIFE. Designed and crafted entirely in the U.S.A. don’t be a stranger. follow us on social media. support@rusticahardware.
