Product Manual

Page 3
QUICK START GUIDE
1. Power Up
Turn the speaker on - using the awning light switch if the light has been connected to
the awning light circuit, otherwise a separate switch or 240V plug pack if fitted.
2. Connect your device.
Open the Bluetooth menu on your device to search for your RV Media Bluetooth
speaker. It’s Bluetooth device name is “RV Media RGB”.
Upon first use, the speaker will not appear on your Bluetooth device list for
approximately 8 seconds. Once the it appears, select “RV Media RGB” to connect.
No pin number or password is required.
2. Listen to Music!
You can stream music to the speaker without using the dedicated app. Use the
volume control on your device to control the volume of the speaker.
3. Get the App
The RV Media free app is available both on the Apple app store
and Google Play. Search “RV Media” to download the app for
your device.
4. Using the app
To use the app, please follow these steps:
a) Turn on the RV Media BT speaker/light
b) Connect your device as per step 2.
c) Open the app. The app will search for the speaker then open
the light on/off, colour selection menu.
d) Use the app to control the light functions.
5. Bluetooth Connection & App trouble shooting.
After first connection of your device to the speaker, the speaker should automatically
re-connect the next time it is powered up (providing Bluetooth is enabled on your
device). If you re-open the app but it fails to re-connect to the speaker, please close
the app then re-open it. Please use the following procedures to close the app:
Apple - double click on the home button to open a list of apps running in the
background then locate the RV Media app and swipe upwards to close the app.
Android - Launch the Recent Applications Menu (this varies from device to device so
check your user documentation if you are unsure how to find this menu). Locate the
RV Media app and swipe to the right to close it.
6. Reconnecting devices.
When you power up the RV Media speaker/light, it will first attempt to reconnect to a
device that was previously connected (this applies to the last 5 devices connected to
the speaker).
.
Page 2
Apple app store QR link
RV INSTALLATION
1. LOCATION
The RV Media Bluetooth Speaker Light is intended to be installed on the exterior of
your RV. It operates on 12V DC and the best location to fit it is in place of an existing
awning light, however you can install it anywhere outside or inside the RV as long as
you can connect it to 12V.
2. WIRING
The Bluetooth Speaker Light is supplied with a power lead fitted with male
& female line plugs. These allow the speaker to be pre-wired and easily
connected by joining the two plugs together. The power plug also allows
for the connection of the optional 240V plugpack plus allows the speaker
to be temporarily mounted if required.
Connection. Simply connect the red wire of the removable end of the
power lead to the RV’s +12V wire & the black wire to -12V. Ensure these
connections are made with suitable crimp terminals or solder & heatshrink.
3. MOUNTING
If installing in place of an exterior awning light, please use the following steps as a
guide:
a. Remove the existing awning light.
b. Mark the location of the 4 mounting screws. Note be careful to ensure the screws
will not damage any materials behind the mounting surface.
c. Mount the optional locating brackets using the centre screw (only) with the hook
part at the bottom. These brackets provide reinforcement for the speaker plus can
be used as a temporary, removable mounting option if required.
d. Connect the power plug to the socket that was wired in step 2. We suggest that
this connection is secured with electrical tape. Mount the speaker using the 4
supplied screws - taking care not to over tighten the screws. Please ensure the
power wire is recessed as much as possible in the hole where it emerges
from; and ensure that any remaining cable is stored in the cavity at the back of
the speaker. Press in the supplied screw covers to hide the screws.
e. Using a suitable RV Sealant, seal around the edge of the speaker ensuring a
water-tight seal to complete the installation or use the supplied sealing foam.
If you are unsure about any elements of these installation guidelines, please
seek the advice of an experienced RV installer or suitable Electrician.
INSTALLATION IN OTHER LOCATIONS
For installations in such as Marine, home Pergolas, Pool Areas and Entertainment
areas; please use the optional RV Media 12V Plug pack (p/n 040855) if a direct 12V
power source is not available. The plug pack features an extra long 3M power cord
to ensure it reaches the Bluetooth Speaker.
Note the plugpack should be located in a dry environment.
Removable end.
Google Play QR app link