Rear View Safety, Inc.
What’s in the Box? • 1 x 7" Quad View Monitor With Built-In DVR and Sunshade • 1 x Universal Mount With Adhesive Pad • 2 x Wireless Antennas
Table of Contents Introduction.................................................................................................. 4 Safety Information ................................................................................. 5-7 Before Beginning Installation.................................................................. 8 Installation Guide........................................................................................ 9 Monitor ...........................................................
Introduction Congratulations on purchasing a Rear View Backup Camera Syste! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle. The Backup Camera System should not be used as a substitute for the standard rear view mirror or for any other mirror that exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
Safety Information INSTALLATIoN • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN No EVENT SHALL SELLER oR MANUfACTURER BE LIABLE foR ANY DIRECT oR CoNSEQUENTIAL DAMAGES of ANY NATURE, oR LoSSES oR ExPENSES RESULTING fRoM ANY DEfECTIVE PRoDUCT oR THE USE of ANY PRoDUCT.
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. Step 1: Choose the monitor and camera locations. Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm) hole should be drilled for passing camera cable through vehicles walls.
Installation Guide Camera Connection: • Locate the clearance lights wiring on your vehicle. You may need to remove the interior panel in order to locate. Connect the power cables for camera: Red wire to light's positive; Black wire to chassis ground. Monitor Connection: • Cigarette lighter adapter: firmly insert the lighter plug to cigarette lighter socket. • Loose lead wire: To power the system connect the power (RED) 12V + wire to ignition power and the ground (BLACK) wire to the chassis ground.
Monitor CAMERA SELECTION DOWN ARROW MENU/ SELECTION BUTTON UP ARROW POWER ON / OFF BACK HOME 10 REAR VIEW SAFETY
System operation System Operation: To turn on the monitor, press “POWER ON” button. To get to Main Menu, press “Home” button use the up and down arrows to navigate the menu and use the "Home" button to confirm your selection. To go back, press the "REV" (arrows) button.
Pairing Pairing 1. Use the "right and left" arrow buttons to toggle through the channels and select the channel you want to pair to. 2. Press "Home" to open the menu and press "Home" again to initiate "pairing mode". You will see the system start counting down from 50 seconds. Once "pairing mode" is active it will last for 50 seconds. 3. Press the pair button on the back of the camera within the 50 seconds and the camera image will appear on the monitor. The system is paired.
Recording Recording: System has capabilities to record all 4 cameras. To start recording, insert a Memory card into the slot on the top of the monitor. You will need to format the card which can be done in the "RECoRD" option in the menu. After formatting, choose the channel you want to record and turn it on. When the channel is turned on, the camera will begin recording when the system is powered on. Overwrite option allows system to continuously record while overwriting the oldest footage.
Screen Rotation There are advantages to rotating a screen either vertically or horizontally.
Image Settings Image Settings: The image can be modified to the driver's specifications. Easily adjust the Brightness, Contrast, and Color to create the optimal brightness..
Playback / Audio Playback: for playback, select the "PLAYBACK option in the menu and use the "HoME" button to select the file you want to play back. The "HoME button also serves and the pause button. Audio: CAM2 is the audio enabled channel. When using a cigarette lighter, audio will be automatically activated. When using loose lead connections the blue wire must be receiving 12V to activate audio.
Grid Lines Grid-lines: The grid-lines will appear on CAM2. With the cigarette lighter connection the grid-lines can be turned on/off through the menu. With the loose lead connections the gridlines are controlled with the reverse trigger wire. When this wire is receiving 12V power the grid-lines will appear.
System Camera Placement Reverse With Confidence™ 18
Monitor Specifications TFT LCD Digital Monitor Screen Size 7” Display format 16:9 / 500:1 Dot Resolution Display Brightness Viewing Angle Video Input Video Source Power Supply 800H x 3 (RGB) 480V 400cd/m2 U:50° / D:60° / R:70° 4 channel 1Vp-p, 75Ω DC 12V(+/- 10%) Power Consumption 5W Video System Auto NTSC/PAL Weight 400G Dot Pitch 0.192H x 0.
Camera Positioning Reverse With Confidence™ 20
Troubleshooting Monitor Displays Blue Screen & Displays No Signal • Check to ensure that the connection to the camera is tight. • Do a hard reset, unplug all cables and power cables leave out for 1 minute and then re-connect them. No Image on Screen • Verify camera is on correct camera input • Verify camera is connected to power/ground Signal Issues • The cable is attached just like the standard antenna by screwing on the connectionThe antenna itself is attached magnetically.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.