Instruction Manual Wireless Backup Camera System 7" Quad View Display with Built-in DVR RVS-4CAM Please read this manual before using the product. It may be different from how it is described in the manual depending on the software version. Rear View Safety, Inc.
In The Box for Standard RVS-4CAM 1 x Color CCD Infra-Red Weatherproof Wireless Backup Camera 1 x 7" Quad View Monitor with Built-In DVR and Sunshade 1 x Universal Mount With Adhesive Pad 3 x Wireless Antennas 1 x Camera Power Cable 1 x Screw Kit for Camera Installation TABLE OF CONTENTS TABLE OF CONTENTS Package Contents / Table of Contents . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Information. . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. SAFETY INFORMATION • While installing the Rear View System be careful with the wire • Use this product within the positioning in order to avoid wire voltage range specified. Failure to damage. do so can cause electronic shock or • The Rear View System should only product malfunction. be used when the vehicle is in • Take special care when cleaning reverse.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot/moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
Operating Precautions 1. The device may be powered by a 12/24 volt battery or the vehicle's electrical system. 2. Make sure all cables are connected properly. Improper cable connections may damage the monitor. Remove the power cable connections when not using the device. 3. The back-up battery may be recharged when the power is on. 4. When battery is fully charged, recharging will automatically stop. 5. If batteries are not used for a while, it may take longer to charge. Warning! PRECAUTIONS 1.
Camera Connection: Locate the clearance lights wiring on your vehicle. You may need to remove the interior panel in order to locate. Connect the power cables for camera: Red wire to light's positive; Black wire to chassis ground. Loose lead wire: To power the system connect the power (RED) 12V + wire to ignition power and the ground (BLACK) wire to the chassis ground. These are the only wires needed to power the system. Press power and "arrow" keys to toggle between different views.
INSTALLATION GUIDE Transmitter for Optional Side Camera Transmitter for optional side camera OPERATION GUIDE 1. The monitor will automatically turn on when connected to a power source. If it is not connected to a camera, it will automatically turn off after 3 seconds. 2. Image will automatically appear on the screen when a trigger is activated. 3. Grid lines can be turned ON/OFF. SAFETY NOTICE This system is designed as a driver's aid.
System Operations To turn on the monitor, press “POWER ON” button. To get to Main Menu, press “Home” button use the up and down arrows to navigate the menu and use the "Home" button to confirm your selection. To go back, press the "REV" (arrows) button.
PAIRING Pairing Pairing: 1) Use "right and left" buttons to toggle and select the channel you want to pair. 2) Press "Home" to open menu and press "Home" (a second time) to start "pairing mode". System will count from 50 seconds. "Pairing mode" will last approximately 50 seconds. 3) Press pair button on back of camera within 50 seconds (step 2) and camera image will appear. The system is paired. NOTE: Make sure camera is receiving power when you pair.
Recording RECORDING Recording: System has capabilities to record all 4 cameras. Start recording: 1) Insert a memory card into slot on top of the monitor. 2) Format the card by entering the Record option. 3) Choose channel to record and turn on. 4) When channel and system are active, camera will record. Overwrite option allows system to continuously record while writing (recording) over the oldest footage.
Image Settings The image can be modified to the driver's specifications. Easily adjust the Brightness, Contrast, and Color to create the optimal brightness. USER INTERFACE 1. Press " ", Choose " " → Adjust image 2. Press " , " to adjust. 3. Press " " to select.
Screen Rotation Settings 1. Press " " , Choose " " → Adjust rotation 2. Press " , " to adjust. 3. Press " " to select. Rotation Options (Vertical + Horizontal) There are many advantages to rotating a screen vertically or horizontally.
Settings USER INTERFACE 1. Press " " , Choose " " → Adjust settings 2. Press " , " to adjust. 3. Press " " to select.
Playback For playback, select the "PLAYBACK option in the menu and use the "Home" button to select the file you want to play back. The "Home" button also serves and the pause button. Audio CAM2 is the audio enabled channel. When using a cigarette lighter, audio will be automatically activated. When using loose lead connections the blue wire must be receiving 12V to activate audio.
Monitor Specification MONITOR SPECIFICATION • • 18 • • • • • • • • • • • • Supports both NTSC and PAL video systems Supports 4 cameras with 3 trigger wires.
Camera Specification Reverse With Confidence ™ CAMERA SPECIFICATION Camera Type 1/4" Sharp® Color CCD Picture Elements 250,000 pixels Gamma Correction r=0.45 to 1.0 Viewing Angle 130° Image Sensor 540 TV lines PAL Output 752 (H) x 582 (V) NTSC Output 769 (H) x 494 (V) Lens 2.
MONITOR AND CAMERA PLACEMENT Placement Butterfly / Fans U-Shape Vertical Stand Camera 3 Camera 2 Monitor Camera 4 20 Camera 1 Rear View Safety
ONE YEAR WARRANTY REAR VIEW SAFETY , INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY , INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY , INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS. THE REAR VIEW SAFETY PRODUCTS ARE NOT A SUBSTITUTE FOR REARVIEW MIRRORS OR FOR ANY OTHER MOTOR VEHICLE EQUIPMENT MANDATED BY LAW.
NOTES Reverse With Confidence ™ NOTES __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ ________________
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.