TM 1
What’s in the Box? TO OUR LOYAL CUSTOMERS: Congratulations on purchasing a Rear View Backup Camera System. With this manual you will be able to properly install and operate the unit. To insure the best performance and avoid any false alarm or function failure, please read this manual carefully and install it accordingly.
Installation Instructions 5.3 Cable connection Instructions: Note: Before installing system let the components of the exhaust system cool down. This will make the installation safer and preclude heat damage to the backup sensor wiring or components. 5.3 Installation Instructions: Monitor: - Attach the monitor to the dash with the 3M sticker. - Connect the camera cable to the YELLOW RCA input labeled AV2 and connect the power wires on the monitor to a 12V power source.
Installation Instructions - Connect the 4 pin connection on the camera to the 4 pin connection on the camera wiring harnass. - Connect the power wires on the wiring harness to a 12V power source from the reverse lights. NOTE: When connecting the power wires, connect the RED to power and the BLACK to ground. Red to back light +12 Black to GND Black to GND red to 12V power 3. Align the host bracket screw groove and the plate screw holes, Locking screw. 4.
Installation Instructions Tools Needed Small flat-tip Screwdriver #2 Phillips Screwdriver Black Electrical Tape Masking Tape Pliers Pencil/Marker Tape Measure Multimeter Testing the system: After installing the system, test the sensors. If you see the sensors but not do not hear an audible alert, press the button on the back of the monitor. Warning: Do not stand behind a moving vehicle death or injury could occur.
Specifications Control box Sensors Sensors Camera Specifications Operating voltage DC9~16V Ultrasonic frequency 40KHz Operating current ≤150mA Detecting distance 0.3~1.50m Camera Angle 120 degree Working temperature -20°C ~ 85°C -30°C ~ 85°C Store temperature Alarm MODE Awareness Distance Sound Digital Display Safe mode 130-150cm Bi...Bi... 1.3m-1.5m Alarm mode 60-90cm Bi.Bi. 0.6m-0.9m Alarm mode Dange mode Dange mode 6 90-130cm 40-60cm 0-40cm Bi..Bi.. BiBi Biiii 0.9m-1.
Installation Instructions / Splicing Installing & Splitting Embedded Monitor Installing sun shield: Put shade cover on the display. Installing back cover: Put the monitor with shade cover in the back cover (only for embedded monitor) Splitting back cover: Hold monitor with 2 hands and detach with fingers, as indicated by arrows. (only for embedded monitor) Splitting sun shield: Take the monitor with the left hand and detach with right hand as indicated by the white arrow. (see below) Splicing 1. 2. 3.
Limitations Limitations: The sensors may not work if an object does not reflect the ultrasonic waves or it has an unusual shape, pole, cardboard carton, tire of bicycle, small or slender tree, rectangular lumber or curbs tone. The sensor may not detect another vehicle bumper if it is too high. Also note: This system has different detection distance to the different object. To the wall, the max detection distance is 1.8m; tho the human body, the max detection distance is 1.
Troubleshooting Troubleshooting: No buzzer or display at power up. 1. Is power wire connected to control unit correctly? 2. Verify(+)12V at control unit when vehicle is in reverse. 3. Verify the ground connection. 4. Have you connected to the correct reversing indicator wire? 5. Do you have a minimum of (+)12V and ground at the display? No reverse image. 1. Is the connection of camera power cable and AV cable are right or not? 2. Is AV cable connected to AV2? Guarantee time:12 months.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
