TM
What’s in the Box? • 1 - Full HD Color Infra-Red Weather Proof Camera • 1 - 7" TFT LCD Color Monitor w/Monitor Mount • 1 - Power Harness • 1 - 66’ Camera Cable • 1 - Power Connection Wire • 1 - Screw Kit for installation Note: Minor details may change based on item configuration 2 REAR VIEW SAFETY
Table of Contents Introduction...................................................................................................4 Safety Information ..................................................................................5-7 Before Beginning Installation...................................................................8 Installation Guide.........................................................................................9 Wiring Camera & Monitor..............................................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
Safety Information INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations.
Installation Guide Cable 1. Be sure to position the cable properly. The camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts. 2. Fasten all cables and secure all excess cable.
Installation Guide The Power Harness. • To power the system connect the power (RED) 12V+ wire to ignition power and the ground (BLACK) wire to chassis ground. • These are the only wires needed to power the entire system and all the cameras. Each camera can be seen at any time by simply pressing the power button and using the V1/2 button to toggle. • The three positive trigger wires each represent one channel and will turn on their channel when the trigger wire is energized with 12V.
Wiring Camera & Monitor • Grid-lines: The grid-lines are also carried through the blue wire. To use the grid-lines for reversing, connect the blue wire to a reverse power. • There is a built-in voltage regulator for our systems which can handle 9-32 volts. Real consumption is 10 to 30 Volts. Note: The camera and monitor can always be activated by manually pushing the power button on monitor. This is in addition to utilizing the positive triggers.
Monitor Wiring Reverse With Confidence™ 12
Monitor Operation DOWN ARROW CAMERA SELECTION MENU/ UP ARROW SELECTION BUTTON POWER ON / OFF V1/V2 ▼ ▼ MENU REV ROTATE IMAGE (Back/Exit when in Menu Mode) • Picture: Toggle picture characteristics (contrast, brightness, saturation, hue, sharpness) to predetermined setting • Contrast/Hue/Brightness/Saturation/Hue: Adjust settings • Front/Back/Left/Right Mir: Toggle normal/mirror image • Dist.
Splitting & Splicing Installing sun shield: Put shade cover on the display. Installing back cover: Put the monitor with shade cover in the back cover (only for embedded monitor) Splitting back cover: Hold monitor with 2 hands and detach with fingers, as indicated by arrows. (only for embedded monitor) Splitting sun shield: Take the monitor with the left hand and detach with right hand as indicated by the white arrow. 1. 2. 3. 4. 5.
Positioning 15 REAR VIEW SAFETY
Monitor Dimensions 7” Rotation Imager Menu/ Camera Up (Exit in Power SelectionSelection Down Arrow Menu Arrow Mode) On/Off Button Reverse With Confidence™ 5.
Monitor Specifications TFT LCD Digital Monitor Screen Size 7” Display Format 16:9 Wide Screen Dot Resolution Display Brightness Viewing Angle 1024 x 600 (RGB) 500cd/m2 Up: 85° Down: 85° Left: 85° Right: 85°4 Video Input Power Supply DC 9V-32V Storage Temperature -20°C ~ +70° C Impact Output 6G Video System NTSC/PAL (Auto Detect) Audio Source Built-In Microphone Audio Output 0.
Camera Dimensions 3” 3.
Camera Specifications High Definition Camera Specs Effective Pixels 1288 (H) x 720 (V) Scan Lines 720 TV Lines, Full HD High Dynamic Range WDR Function Imaging (HDRI) Lens (Wide Dynamic Range) View Angle 130° Power Consumption IR on Max (180 mA) Usable Illumination Power Source IR off Max (180 mA) 0 Lux (IR On) DC 12V+/10% S/N Ratio More than 48dB Waterproof Rating IP69K S/N Ratio ≥ 50db (AGC Off) IR Switch Control Auto CDS or Manual Audio Source Built-in Microphone Storage Temper
Troubleshooting Monitor Displays Blue Screen & Displays No Signal trigger on power harness is put to power 12v+. If the problem still persists, verify that alternate ports work. If alternate ports do not work, remove Blue Trigger wire from 12V+ and select alternate channels. • Do a hard reset, unplug all cables and power cables leave out for 1 minute and then re-connect them. • Check to ensure that the connection to the camera is tight.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
Take Notes ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ _________
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
