Instruction Manual 7” Waterproof Quad View Monitor RVS-9900Q Please read this manual before using monitor. The product may be different from how it is described in the manual depending on what software version you are using.
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 08-09 Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14 Connections. . . . . . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • This Rear View Camera System is designed to help the driver safely detect people and/or objects, helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified. Failure damage.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
INSTALLATION GUIDE Wiring After connecting the monitor to the power harness, plug the camera into the CAM 3 input. Connect the RED 12V power wire to an ignition power source and the BLACK 12V ground wire to a chassis ground. The BROWN wire is the REVERSE trigger wire. Connect this wire to the vehicle’s backup light circuit to activate the rear view image whenever the vehicle shifts into reverse. To attach a second camera, connect it to the CAM 1 input.
Precautions For Use Of Monitor I. The monitor is made of glass and plastic. Do not subject it to a mechanical shock by dropping it from a high place, etc. II. Do not apply excessive force to the monitor surface or the adjoining areas since this may cause the color tone to vary. III. IOnly clean with a soft dry cloth and/or Windex. IV. Do not attempt to disassemble the mirror monitor.
COMPONENTS Components 10 Rear View Safety
7” Waterproof Quad View Monitor with a TFT LCD digital color touch screen display. Monitor comes with a U-Bracket, swivel head mount, and a waterproof rating of IP69K.
MONITOR Monitor Dimensions 12 Dimension 7” TV System NTSC/ PAL Resolution 800 x 3 (RGB) x 480 Brightness 400 cd/m² Contrast 500 :1 Viewing Angle U: 50°/ D: 60°, R/L: 70° Aspect Ratio 16:9 Operating Temperature -10 ~ +65ºC Storage Temperature -30 ~ +80ºC Power Consumption Max. 25W Power for Cameras Max. 4×300mA, 12V Dot Pitch 0.192 (H) x 0.
MONITOR Reverse With Confidence ™ 13
MONITOR 1. Remote control signal sensor 2. Power button 3. Increase / decrease volume and switch sub-menu values 4. Menu selection and toggle display mode (SINGLE/DUAL/TRIPLE/ QUAD/PIP IMAGE) 5. Menu button 6.
Connections CONNECTIONS Reverse With Confidence ™ 15
REMOTE Remote Operations 1. MUTE: MUTE / UNMUTE volume 2. POWER: Turn monitor ON / OFF 3. MENU: Toggle between menus 4.
5. DN: Toggle selection DOWN & toggle display mode (SINGLE/ DUAL/TRIPLE/QUAD/PIP IMAGE) 6. VOL: Decrease volume & toggle sub-menu values 7. VOL: Increase volume & toggle sub-menu values 8. MODE: Toggle display mode (SINGLE/DUAL/TRIPLE/QUAD/PIP IMAGE) 9. SEL.: Toggle jump key 10. P/N: Toggle between PAL/NTSC 11. LANG: Toggle language 12. REST: Restore factory settings 13.
On-Screen Display (OSD) OSD SETUP • SCALE: Toggle distance grid lines ON/OFF. When ON, distance grid lines will be displayed when backup camera (CAM 3) is triggered. • INPUT SCAN: Toggle camera input auto identification. When ON, monitor will display connected cameras and skip inputs not connected. • BOUNDARY: Toggle border color between camera inputs (WHITE/GRAY/ BLACK/UNCOLORED). • LANGUAGE: Toggle OSD language (ENGLISH/FRENCH/DUTCH/SPANISH/GERMAN). • Software version appears under LANGUAGE.
Trigger Setting • TURN IMAGE: Display options when side cameras (CAM 1, CAM 2) are triggered. When on SINGLE, the corresponding camera will display when either camera is triggered. When on SPLIT, a split image of side and rear view camera will be displayed when either side camera is triggered. • REAR IMAGE: Display options when backup camera is triggered. When on BACK, just the backup camera will display when triggered. When set as TRIPLE, the left, right, and backup camera will simultaneously display.
MENU AND TOUCH-SCREEN OPERATIONS JUMP KEY Jump Key Rear View Safety 20
• REC-V OUT: Toggle which camera view will record when a DVR is attached (LEFT/RIGHT/FRONT/QUAD). • AUTOSCAN: When setting is ON, the monitor automatically switches between connected camera inputs and quad view. • SCAN DELAY: Toggle AUTOSCAN delay (0-60 seconds). • JUMP KEY: Toggle jump key destination. Select from 13 display modes as shown on the left. • POWER ON: Toggle default display mode. Select from 13 display modes as shown on the left. • SYSTEM: Toggle PAL / NTSC.
TOUCH SCREEN OPERATIONS When in quad view, press any channel to view full screen 22 Rear View Safety
Touch screen menu TOUCH SCREEN OPERATIONS Reverse With Confidence ™ 23
TOUCH-SCREEN TOUCH SCREEN OPERATIONS OPERATIONS Swap display position (quad view) 24 Rear View Safety
Swap display position (dual/ triple view) TOUCH SCREEN BASICOPERATIONS FUNCTIONS Switch to next display mode Switch to previous display mode Reverse With Confidence ™ 25
CAMERA Camera Dimensions • • • • 26 18 infra-red illuminators (enables you to see in total darkness) 1/4 Sharp® color CCD, 250k pixels, 2.
Reverse With Confidence ™ CAMERA SENSOR 1/4” SHARP® COLOR CCD PICTURE ELEMENTS 250,000 PIXELS GAMMA CORRECTION R=0.45 TO 1.0 IMAGE SENSOR 600 TV LINES, PAL: 500 (H) X 582 (V) NTSC: 510 (H) X 492 (V) LENS 2.
Troubleshooting Problem Possible Causes/Solutions No picture/sound No picture No sound TROUBLESHOOTING Dark picture No color Upside down/inverted picture Backup camera does not display when car is in reverse Adaptor is connected incorrectly. Improper power supply. Unit is off. Check cable connection. Audio cable improperly connected. Volume is off or set very low. Adjust brightness/contrast. Low environmental temperature. Adjust the color settings.
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS. THE REAR VIEW SAFETY PRODUCTS ARE NOT A SUBSTITUTE FOR REARVIEW MIRRORS OR FOR ANY OTHER MOTOR VEHICLE EQUIPMENT MANDATED BY LAW.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
