Instruction Manual G-SERIES Backup Camera System with Bluetooth RVS-776718-BT Reverse With Confidence ™ Rear View Safety, Inc.
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . .
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury. However, you the driver, must use it properly.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly.
INSTALLATION GUIDE Clip-On Monitor 1. The Mirror Monitor attaches to the existing rear view mirror in vehicle with the pressurized clips on the back of the monitor. 2. Attach monitor to existing mirror, and adjust mounting angle to allow optimum driver viewing comfort. Camera & Cable Be sure to position the cable properly. The aviation camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements.
FIGURE 1.1 10 INSTALLATION AND WIRE INSTALLATION AND WIRE FIGURE 2.2 FIGURE 1.
About Our Monitor FIGURE 2.1 10.25” 12 SPECIFICATIONS: Screen Size: Display Screen: Display Resolution: Aspect Ratio: Color Depth: Pixel Pitch (mm) Power Consumption: Working Voltage: Video Input: Signal System: 4.3” TFT-LCD 400(H)x272(V) 16:9 16.7M dithering 0.219x0.219 8W DC 9V-32V NTFS/PAL Video input PAL/Auto/NTSC Rear View Safety 1. RED- Power (+) 2. YELLOW- Video 3. GREEN- Mirror / Normal Imaging 4. WHITE- Audio 5.
Camera Installation 14 SPECIFICATIONS: Mounting Position view angle installation Rear View Safety position 170º Reverse With Confidence ™ CAMERA INSTALLATION CAMERA SPECIFICATIONS About Camera 15
Long press the settings button to enter into “grid-line adjustment” mode. The upper half of the remote is used to adjust the left grid line while the bottom half of the remote is used to adjust the right one. The up, down, left and right buttons are used to adjust the location of grid lines. The clockwise rotation contra rotation buttons are used to adjust the angle of grid lines. It is easy to operate and calibrate. Accuracy The accuracy of the grid-lines can vary based on how you angle your camera.
BLUETOOTH CONNECTION Manual Bluetooth Connection If your phone is not connected to the rear view mirror and the screen is off, long press the center button to manually reconnect Bluetooth. Connecting To A New Phone Once a minute has passed after the system turns on, connect your mobile phone or other device to the rear view mirror. Successfully Connected After the password has been set, a Bluetooth icon will appear on the monitor. This indicates a sucessful connection.
Backup Camera Display And Manual Brightness Adjustment After installation, place the vehicle in reverse and the backup camera image will automatically display on the monitor. Once this image is displayed, you can manually adjust the monitors’ brightness by pressing the center button. The brightness can be adjusted from 10 to 100. The OSD menu will disappear after 5 seconds of inactivity.
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
A Safe Fleet Brand If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
